Maintenance & Repairs - March 2007

My friend wants to have te timing belt changed on his 907 onda Accord. How difficult a job is this in terms of accessing the belt?

2007-03-25 06:35:41 · 4 answers · asked by afreshpath_admin 6

someone brought me this car to fix, she was told water pump and has already purchased a new one. I'm pretty knowledgeable about cars, but...

2007-03-25 06:33:41 · 3 answers · asked by runzwitbeer 1

my XR2i has rust around the the chassis stamp (under the carpet by drivers door) the numbers are getting a little illegible, if it rots through what can i do?

i can weld over the chassis stamp can i? that would make it a potential ringer?

and no, im not gonna scrap it.
thanks

2007-03-25 06:32:50 · 4 answers · asked by handsonhips101 4

2007-03-25 06:29:01 · 2 answers · asked by Anonymous

2007-03-25 06:28:32 · 5 answers · asked by bearman48064 3

2007-03-25 06:26:50 · 2 answers · asked by bearman48064 3

2007-03-25 06:26:41 · 3 answers · asked by Anonymous

was driving the car the other day had gas and oil and all fluids topped off car was acting fine then the oil light and service engine soon light came on and it shut down and wouldnt start did fuel and oil test on it getting both but just wont start,it acts like it wants to but it wont please help

2007-03-25 06:20:04 · 6 answers · asked by jambcombs4321 1

2007-03-25 06:17:26 · 1 answers · asked by Danielle 1

2007-03-25 06:10:59 · 3 answers · asked by bearman48064 3

2007-03-25 06:05:15 · 8 answers · asked by timothy c 1

Is there anything else that I can do besides smaller tires or a lift kit. The rear is fine but all the trouble is in the front. Ive tried the rubber coil boosters and it didnt work.

2007-03-25 05:54:25 · 3 answers · asked by lilsoulja337 1

2007-03-25 05:37:16 · 2 answers · asked by lyn p 1

The blower switch in my chevy malibu 1998 LS does not work at position 1 and 2. There is nothing wrong with the switch and switch board itself. I have tested it. Also, it works fine at the other positions. Its like that ever since I bought that car (2 years ago). Any sugestions will be greatly appreciated.

2007-03-25 05:36:29 · 5 answers · asked by umermariner 1

I have a 95 mitsubishi eclypse. I have had a tune up, oil change, and ingnition module cleaned. I just had a fuel pump put in it this past moday. What was happenning was that i would drive about an hour and it would shut off not stall just shut off. Now i drove it yestorday and the rpm would want to go up... i would be steady with the gas and the needle would move up and then down not past 1rpm then i got to a stop sign and it just died again. what could be going on?

2007-03-25 05:33:41 · 5 answers · asked by Elicia 1

ive got it un bolted but i cant get out up there the exaust manifold do i need 2 take the cylnoied off 2 get it out

2007-03-25 05:31:28 · 3 answers · asked by jaydbme 1

im tryin to gettin the spray paint off my finish..it is stuck on there pretty good..would buffing it out help, and do u have any tips to minimize effort? thanks everyone

2007-03-25 05:24:50 · 5 answers · asked by wizzpack 2

I have a toyota lancruiser turbo diesel and i live in a very hilly region. I often downshift to 2nd gear going downhills to spare my brakes. Does this make it more likely for me to have transmission problems?

2007-03-25 05:24:09 · 10 answers · asked by misoma5 7

I just pulled out my EGR valves and cleaned out the carbon off of it since I failed my DEQ test. Their computer said that I had problems with my Exhaust gas reciculation. I pulled that ERG, cleaned it thouroughly now is in need of reseting the "check engline" light off. Thank you .

2007-03-25 05:23:43 · 8 answers · asked by Felipson R 1

when we pull off from traffic lights or from a roundabout, it's taking it's time, gaining speed.
can anyone give advice on what to look for, or the reason why.

2007-03-25 05:22:37 · 8 answers · asked by madmactouche 1

my car is a 94 mercury villager mini van. when i put into gear it dies so i have to keep one foot on the gas and one on the brake

2007-03-25 05:21:46 · 4 answers · asked by Anonymous

im havin my mechanic replace the cam on a 4 cyl chevy engn, he says i should do a valve job on it also but hasnt given me a price yet .He's already got 1100 for pullin the engn, acid bath, replace cam, im wonderin what the ballpark$ amount should be to have the valve job done also. no boring.

2007-03-25 05:21:11 · 3 answers · asked by Anonymous

The back tyre on my scooter has gone totally flat and it wont pump back up, i don't think it's punctured the air is going straight out round the rim where it's supposed to seal. Can i pump it up somehow?

2007-03-25 05:20:18 · 4 answers · asked by Rob S 1

2007-03-25 05:10:12 · 20 answers · asked by dougster 1

2007-03-25 05:02:35 · 2 answers · asked by tankmech4 1

When I step on the gas it just sputters and sends a lot of exhaust out the tail pipe. I has also been backfiring a little bit. I changed the fuel filter and the fuel pump is working perfectly. Any ideas?

2007-03-25 04:57:34 · 6 answers · asked by Brad 2

my car is a 94 mercury villager mini van

2007-03-25 04:49:32 · 3 answers · asked by Anonymous

Is there only 1 way to put the wiper motor in or can u accidently install it upside down causing the wipers not too function?

2007-03-25 04:35:45 · 3 answers · asked by Henry M 1

2007-03-25 04:35:39 · 2 answers · asked by Anonymous

2007-03-25 04:32:12 · 4 answers · asked by Anonymous