Cars & Transportation - 26 August 2007

i would like to know.

2007-08-26 13:05:45 · 3 answers · asked by acosteguin79 1 in Maintenance & Repairs

I checked walmart but the blades did not look like they fit

2007-08-26 12:57:56 · 16 answers · asked by Anonymous in Pontiac

thanks ;)

2007-08-26 12:57:50 · 4 answers · asked by Anonymous in Toyota

How do you tell if it's bad? Can it be tested?

2007-08-26 12:42:17 · 4 answers · asked by Anonymous in Honda

2007-08-26 12:39:44 · 2 answers · asked by brady g 1 in Motorcycles

I was told I need to run the generator until all the gas is used up. Is that necessary? Can I just put some stabil in and leave it?

2007-08-26 12:37:49 · 6 answers · asked by ld040318 2 in Boats & Boating

do you know a website that will tell me what the 3 major american car companies ( ford, gmc, and chrysler ) own

2007-08-26 12:36:53 · 4 answers · asked by Emma R 1 in Other - Car Makes

Its making the motor oil leak.. its a 17mm hole.

Thanks

2007-08-26 12:17:05 · 7 answers · asked by neopiancardcaptorirene 2 in Maintenance & Repairs

Main reason eletric motors will they stand up to long run times or struggle all the way. Only America and a few other country uses 60hz. i want to get some tools but i need some info. i live in a 50hz enviroment. or if there is a converter and can it run 200 amps.

2007-08-26 12:14:10 · 3 answers · asked by leon c 2 in Maintenance & Repairs

and do i need special tools?

2007-08-26 12:11:56 · 3 answers · asked by elizabet 3 in Maintenance & Repairs

the gas station with the air pump is a few miles away, so obviously the tires wouldn't be cold. how much should i put in the tires if my car is recomended 29 psi cold inflated?

2007-08-26 11:59:37 · 5 answers · asked by Ripcity-zen 2 in Maintenance & Repairs

Any idea what's causing this? If I have to take it to a mechanic, any idea what it might cost? I don't want to sound to dumb, cause I don't know much about cars. Thanks for any help you can give me!

2007-08-26 11:52:17 · 6 answers · asked by SinSister 5 in Maintenance & Repairs

The model# A M55RSLH and serial# A 01603804. It has an Evinrude cover on it and is a 55 horse power.

2007-08-26 11:49:12 · 2 answers · asked by Anonymous in Boats & Boating

my car is 17 years old

2007-08-26 11:41:13 · 13 answers · asked by Anonymous in Maintenance & Repairs

I have a 00 Montana with a blown head gasket. The mechanic said it would be a 700 dollar repair. This seems like too much money. Does this seem right? Has anyone had this done or know what the labor rate is on a repair to these types of vans?

2007-08-26 11:38:32 · 8 answers · asked by Lo-Boy 2 in Maintenance & Repairs

parts , how to repair

2007-08-26 11:35:51 · 4 answers · asked by Anonymous in Motorcycles

I already replaced oxygen sensor the first time it came on.

2007-08-26 11:32:01 · 4 answers · asked by John71 3 in Acura

First of all let me just say im not familiar with cars and this is my first. My car coolant which i presume makes a weird hss noise after i turn off the car, is this something I should be worried about?

2007-08-26 11:31:59 · 6 answers · asked by Anonymous in Maintenance & Repairs

2007-08-26 11:29:07 · 11 answers · asked by Anonymous in Other - Cars & Transportation

2007-08-26 11:23:39 · 12 answers · asked by Anonymous in Aircraft

2007-08-26 11:23:14 · 1 answers · asked by antisus p 1 in Motorcycles

I just recently had my catalytic converter changed and less then a week after it was replaced the check engine light went on in my 1996 Honda Accord. I brought the car back to the mechanic and they told me that the 02 sensors need to be replaced. I was wondering if it is likely that the 02 sensors failed because of their faulty work in the replacement of the CAT, or is it more likely that the CAT needed to be replaced because the O2 sensors were bad?
Also does anyone have any idea what it should cost to replace the O2 sensors on a 96 Honda Accord?
Thanks in advance for any advice you can provide

2007-08-26 11:23:00 · 5 answers · asked by Justin 1 in Maintenance & Repairs

2007-08-26 11:22:44 · 3 answers · asked by Anonymous in Chevrolet

2007-08-26 11:19:45 · 8 answers · asked by loghog751 2 in Other - Car Makes

2007-08-26 11:18:49 · 8 answers · asked by Anonymous in Chevrolet

I am in the process of rebuilding a 1972 chevy truck and need to find a print out of a wiring diagram for this truck any help

thanks

2007-08-26 11:13:20 · 0 answers · asked by daphne w 1 in Maintenance & Repairs

i have a 2004 chevy silverado and can not figure out why the driving lights will not light up on my trailer. The lights work with my other truck so I know it is not the trailer. any one have any ideas what it might be and how to fix it in a hurry
i have checked the fuses and they seem to be fine

2007-08-26 11:10:44 · 6 answers · asked by dave p 1 in Maintenance & Repairs

2007-08-26 11:10:23 · 2 answers · asked by Sexy Ray 3 in Maintenance & Repairs

This is a new one on me. I have recently decided to replace the split bench seat in my '03 Ram 1500 with an older style Ford bench seat. I haven't even taken the measurements yet, because I would like to know what the best option would be. Are there any older seats that might match the bolt patterns, or is the only option to drill new mounting holes? I know its really one of those "Had to have done it before" questions, so I'm hoping someone out there has done this!

2007-08-26 11:07:18 · 1 answers · asked by stolen_thunder2003 2 in Maintenance & Repairs

hi i have a 1986 nissan maxima and i JUST changed the oil...the gauge worked fine be4 the change but 2 minutes into my "first run" after the change...the psi gauge fell to 0 and stayes there....even when i have the key switched into "on" with the engine off, when i usually hear rrrrrrr and the gauges go to 90 psi normally...and now....nothing is it bad to drive the car?....i got new oil filter and am using valvoline maxlife synthetic blend

2007-08-26 11:06:32 · 4 answers · asked by Anonymous in Maintenance & Repairs