Maintenance & Repairs - September 2006

Some little prankster decided to scratch up my front and rear windows of my van. What can get them off WITHOUT replacing them? And without the expense of a shop visit

2006-09-16 13:10:57 · 3 answers · asked by Anonymous

we moved it to flat ground and it still wont start. it turns over so i know it is not the battery. it just wont start PLEASE HELP

2006-09-16 12:39:49 · 8 answers · asked by beverly s 1

for a 1997 dodge neon engine with a 2.0 sohc i need to to get the bottom timing gear off. the ine that hooks onto the crankshaft. its belt timing.

2006-09-16 12:24:59 · 7 answers · asked by huttman6021 1

It's an 81 ford mustang 2.3L everytime we run it. It melts the cam bearings. HELP

2006-09-16 12:22:22 · 5 answers · asked by strokerace23_99 1

My friend,a girl, went to a mechanic to get the brakes fixed on her car, and they estimated almost $3,000!!! Her husband took it somewhere else and they estimated only $800. The first place also told her that something was wrong with the transmission and she would have to come back in soon to get it fixed, whereas the other place said everthing was fine... Is it true that auto shops always see a sucker when a woman walks into the shop alone?

2006-09-16 12:07:10 · 13 answers · asked by BoMbS_aWaY 2

2006-09-16 12:03:56 · 4 answers · asked by Crankshaft 1

I had my oil changed today and I have 123,000 miles on my car. I have regular oil changes. Jiffy Lube recommended that I have a engine flush done on my engine, because it needed it. I OK'd it. I only live a few blocks from jiffy lube and did not notice anything different except I didn't have as much oil pressure as usual. Later that day I had to go to a funeral and drove approx 10 miles and when I stop for a light, my engine oil light came on and my engine pressure drop to almost 0. I stop for about an hour and when I started it up the pressure was up alittle and then it drop again.

2006-09-16 11:57:19 · 4 answers · asked by Mike m 1

They are already installed. How do I make then fit the diskbrake?

2006-09-16 11:46:24 · 11 answers · asked by alicia g 1

1999 GMC Safari 4.3. The engine turns over but will not start. I changed the fuel filter and the fuel pump is working, but it still won't start.

2006-09-16 11:33:28 · 12 answers · asked by Anonymous

i have a 95 ford explorer, and the gas gauge does not work,im thinking the float is bad,can any one tell me where the float is located?

2006-09-16 11:23:06 · 11 answers · asked by carlton o 1

2006-09-16 10:51:33 · 12 answers · asked by Netinho 1

2006-09-16 10:47:58 · 2 answers · asked by solis5639 1

2006-09-16 10:43:43 · 2 answers · asked by generousgg 1

I have had a brake job done on a 92 sentra new rotors and cramic pad on front. Turned rotors new lifetime shoes on back! after about a week after the brakes got a little heat(after driving about 40 miles) on them they started sweking & making a scraping sound I took it back to the shop they said every thing is wearing right of coarce when they test drive it its cold no noise what is the cause?

2006-09-16 10:41:20 · 6 answers · asked by Stryker-58 2

I have a problem with my keyless entry/car alarm system. I have the system that locks the car automatically after 10 seconds. And if i don't open the car with the Remote and use the Key, the system ticks and ticks, usually until i find the remote and click it. But now the remote does nothing and the car ticks all the time until the battery dies. Or until i remove the system. :( PLEASE HELP!!!

2006-09-16 10:36:06 · 13 answers · asked by Andrew 2

i had an unusual first time experence today, flat tire, thanks to my dad he watched me but i demanded i learn the hard part is the lug nuts, un screwing them with the wrench, what is an easy way to un screw them, oil or what. thanks

2006-09-16 10:29:11 · 11 answers · asked by debbigeri 3

i sanded the fenders on my bike with 150 grit. I primed one piece and i noticed in the areas where i had to use some extra force (decal glue, ripples in clear coat) it showed through the primer as little scratches. Now, i have to sand the whole bike again with like 250 grit. Is there anything else i can do? (please no comedians im kind of pissed about this)

2006-09-16 10:28:39 · 4 answers · asked by skatrman010 2

2006-09-16 10:21:29 · 6 answers · asked by remsunrise 1

2006-09-16 10:09:40 · 10 answers · asked by Kim M 1

Whenever i hit the brakes the car shakes, I have had the car alignment done that isn't the problem does anyone know what the problem could be and how easily it could be fixed?

2006-09-16 10:08:05 · 13 answers · asked by Koll 2

Like the AC, does the engine have to be running for the heater to work in a car or can it operate just with the ignition on?

2006-09-16 10:06:51 · 12 answers · asked by audiguy 41 2

it seems fine when driving locally but whan i go faster speeds like on highway the resovior empties of antifreeze not overheating cannot find any leakage please help

2006-09-16 09:34:36 · 3 answers · asked by amy22_01835 1

I've heard to put about 3 bottles of HEET in my car and rev up the engine to fix this problem. The NOx limit is 2.00, my car had 3.5085 at the time of the test

2006-09-16 09:08:21 · 9 answers · asked by LMP 1

Will using 10w30 oil instead 5w30 on my 2003 Camry create any problems? Is there any long term problems. My manual says to use 5w30 but is 10w30 that much of a difference.

2006-09-16 09:05:07 · 16 answers · asked by 34 RIP 3

2006-09-16 08:54:33 · 10 answers · asked by CHUCK D 1

2006-09-16 08:45:39 · 6 answers · asked by jimbo 2

basic repairs. eg: headlight replacement

2006-09-16 08:37:20 · 4 answers · asked by Perico 1

Would like to use it to plug a small hole in the bottom of a gas tank.

2006-09-16 08:23:47 · 4 answers · asked by swahrends 1

2006-09-16 08:13:15 · 3 answers · asked by jablonsj 1

2006-09-16 08:09:30 · 5 answers · asked by nw44tg 2