Cars & Transportation - 8 July 2006

About two weeks ago a rock chips and crack my windshield about 2 inch , now the crack about 10 inches. do i need to replace it or can it be repaired?

2006-07-08 03:00:41 · 7 answers · asked by Anonymous in Maintenance & Repairs

I specifically need just the rear half of my chassis. It has rusted and broken right where the bed meets the cab. So, I really could use the drawing and measurements of the raw chassis with locations of exact holes for the spring brackets and etc. Ford Ranger, VIN 1FTYR14CGWPA12088. Thanx a million!

2006-07-08 02:59:49 · 3 answers · asked by gus 1 in Maintenance & Repairs

How much should I expect to pay for a oil change?

2006-07-08 02:58:50 · 8 answers · asked by imports_75 1 in Motorcycles

Metal chip backwards on windshield. Cannot get off. How can I do it without breaking the windshield?

2006-07-08 02:54:18 · 9 answers · asked by Anonymous in Maintenance & Repairs

When i pulled my old radio out of my 94 ford aerostar there was no red power line, my cd player had one by not the radio how do i figure out which one is the power line and which is the speaker line and etc?

2006-07-08 02:51:14 · 4 answers · asked by Anonymous in Car Audio

For the past few weeks it smelled like gas when idleing. My husband parked it 3 days ago and when he went back out it would not start. It turns over fine (we replaced the starter last week), and we have spark, but nothing. We have replaced the fuel filter and the distributor cap. Any ideas what could be wrong? I think it could be a bad coil or possibly a fuse.

2006-07-08 02:50:13 · 11 answers · asked by kefowler7 2 in Chevrolet

Had an accident yesterday. It is not my fault. The other driver has insurance. We contacted the other car insurance company. Should I report this to my insurance company or not? If YES or NO please let me know why. Both insurance company are very reputable companies.

2006-07-08 02:48:31 · 9 answers · asked by IronMan 1 in Insurance & Registration

2006-07-08 02:43:45 · 10 answers · asked by Anonymous in Maintenance & Repairs

2006-07-08 02:42:00 · 8 answers · asked by Anonymous in Maintenance & Repairs

2006-07-08 02:40:16 · 12 answers · asked by Anonymous in Maintenance & Repairs

with engine knowledge...yesterday I was under a 1/4 tank of gas - we have a Ford Taurus (unfortunately, it sucks - a 96). I put $20 in the tank. We've had financial issues lately and I've been putting the cheapest gas in. Anywy, the car ran ok for a bit without driving very far. This morning I got in the car and it is like sputtering and acting like it wants to stall at the light and all. Does this sound like I got some bad gas possibly or something more serious? I'm praying for some good answers - our only car left. If I did get bad gas, is there something I can do to correct it now or do I have to wait until I'm on empty again?

2006-07-08 02:38:51 · 16 answers · asked by Anonymous in Maintenance & Repairs

2006-07-08 02:38:10 · 9 answers · asked by Deanna M 1 in Insurance & Registration

Where on the Vehicle are all the VIN Numbers Located?

2006-07-08 02:27:24 · 13 answers · asked by wardenrepublic 1 in Maintenance & Repairs

I recently purchased a 94 Windstar (14000kms) and the ABS light is comeing on. There is a noise comeing from the brakes when I use them. Any idea of the cost/repairs required?Thanks in advance. Bertram

2006-07-08 02:22:10 · 3 answers · asked by timethrift 2 in Maintenance & Repairs

Trying to stop juddering and cutting out - my friends advise me it is points and plugs - can't find distributor.

2006-07-08 02:21:05 · 8 answers · asked by susansmoreland 1 in Fiat

I have removed the air box and mass air sensor, but i now have no clue as to where the bracket (which was supplied) is connected to.... help please!

2006-07-08 02:12:23 · 1 answers · asked by Anonymous in Maintenance & Repairs

Need help - Anybody know the radio code for a 01 Prelude. I don't have the manual and the dealer wants to charge $50.
thanks

2006-07-08 02:11:08 · 1 answers · asked by Pipo 2 in Car Audio

is it cheaper to change my 92 corolla shock absorber in singapore or in JB ? How much to change the front set?

2006-07-08 02:07:53 · 2 answers · asked by Ruhua 2 in Maintenance & Repairs

It makes that noise as the RPMs go up. Now it just crawls along and has trouble changing gears. Is it the alternator?

2006-07-08 02:06:53 · 7 answers · asked by Anonymous in Maintenance & Repairs

2006-07-08 01:59:53 · 10 answers · asked by Georgia B 1 in Aircraft

2006-07-08 01:59:06 · 5 answers · asked by magnum_feb1990 1 in Other - Cars & Transportation

the clarion cdc 6700r was standard fitment to my Peugeot 205gti 1fm so i would like to buy one to keep the car origanal.

2006-07-08 01:54:19 · 3 answers · asked by STEVEN C 1 in Car Audio

2006-07-08 01:46:22 · 2 answers · asked by William B 1 in Maintenance & Repairs

am looking for a 7 seater car and am stuck would like to know what makes of the cars and there names please. thanks

2006-07-08 01:44:45 · 8 answers · asked by Anonymous in Buying & Selling

2006-07-08 01:23:54 · 10 answers · asked by Mayuresh 2 in Motorcycles

I have two cutom dynamics hard boards.but at a loss as to how to encase them/waterproof

2006-07-08 01:22:52 · 3 answers · asked by Anonymous in Motorcycles

We need to know how to disable the passenger-side airbag on a 2006 Chevy Uplander. We can see an off/on indicator on the dash, but it doesn't appear to be a control button. This is a rental car and did not come with an owner's manual.

2006-07-08 00:59:51 · 2 answers · asked by Anonymous in Safety

he gets angry faster

2006-07-08 00:42:43 · 21 answers · asked by Anonymous in Safety

2006-07-08 00:38:53 · 4 answers · asked by MeLissa 3 in Car Audio

I was sold a drive shaft from advanced auto parts and I think it was .001 to .002 small is was not much. I am not really sure now as it has taken out the input guide/shaft holder. I dont know what to call it. The part in the transmission that holds the shaft.
When I put it in 5 months ago or so I did not feel the slop. that is why I say .001
What do I do now it has ruined my transmission. I have asked the neighbor next door (ase) certified, does he think it was my fault. He says no. I have also talked to another mech. Before I found out what the problem really was and he told me that they have had problems with the place I bought the shaft. They dont deal with them anymore.
I am almost 100% sure it was a manufacturing error. Has anybody had this problem and can I sue to have my transmission replaced?

2006-07-08 00:29:03 · 2 answers · asked by twocooldrew 2 in Maintenance & Repairs