Car Audio

how can you feed theem more power with out blowing them. sparky you say they can take 10000 to 15000rms

2007-01-18 00:39:14 · 3 answers · asked by johnmsixpack 1

getting a decent bass tube and amp. wondering if the sound system will sound rubbish if my midrange speakers dont match in quality.

2007-01-17 21:54:11 · 12 answers · asked by Anonymous

my head unit (Sony cdx-gt500) has subout connection(red and white), do i just plug in subwoofer into that and will work ? or more step require ?

2007-01-17 18:26:14 · 7 answers · asked by haha 1

I need to replace this stereo anyway since it doesn't play CDs anymore, plus I'm having problems holding the cup when I drive.

2007-01-17 17:44:35 · 3 answers · asked by laxeroflax04 2

OK, so I have an Alpine MRP-M850 (rated at 800W at 2ohms) that I will be using to push a Kicker CVR12 (max: 800W rms:400W).

My question is what gauge power and ground cable should I use to wire it all up? Also what size fuse should I use (the emphasis on the fuse being to protect my car and my equipment, obviously I would rather replace a fuse and have to turn down my gain than blow my amp or worse burn down my car)?

In my old car I had it hooked up with 10ga over 15ft, with a 30amp fuse. I was fully aware of what I was doing at the time and the gain on the amp has never been higher that 30% for safety's sake. But I've got a new car and it's finally time for me to crank up my amp and see what she can do.

2007-01-17 14:27:24 · 7 answers · asked by Dame 2

What hits harder and is more of a punch than a rumble?

2007-01-17 12:31:03 · 7 answers · asked by Anonymous

Anyone who has seen the trunk of a '02 impala knows it's rather large, I was first going to atempt 15" Solo-Baric Kicker subs but was told that there would not be enough air space for them to vent properly, so I was wondering would 12" Solo-Baric Kicker subs work better or at all?
Thank you for your answers to anyone who can be of assistance.

2007-01-17 10:31:01 · 2 answers · asked by prophet_bhgf 1

I guess I want you just to vote, then tell me why you choose it.

An Alpine audio system vs An Clarion audio system?

2007-01-17 09:39:44 · 7 answers · asked by Anonymous

I plan to simply replace my factory speakers with some good component speakers and a 4-channel amplifier. I don't like exaggerated bass, so would I still need subwoofers?

2007-01-17 09:25:02 · 11 answers · asked by Trick of the Tail 4

cigarette ligter fitted or is there something that i can buy ? thanks

2007-01-17 08:40:25 · 6 answers · asked by Anonymous

I blew a cheap subwoofer and am curious on how to fix it. It is a tube subwoofer if that helps, a 6 inch.

2007-01-17 08:37:55 · 4 answers · asked by Cory 1

i have 2 10 inch subs in my car that really bass and vibrate but its made of a paper cone, is paper cone not good at bass or does it loose intensity over time?

2007-01-17 07:30:49 · 3 answers · asked by Eugene 3

ok i have a rover 214 and have replaced the head unit, can anyone tell me what size the speakers are which go in the front doors?

also is there anywhere for tweeters, i cant see any ?

and a general question now...... 6x9 speakers ?
i know they go in the parcel shelf but how do they get there, do you have to cut the holes out yourself of do u buy a pre-cut parcel shelf?

if you have to cut yourself, is there a template you can buy so you dont scre up?

cheers

2007-01-17 07:25:31 · 2 answers · asked by Anonymous

on a car speaker, there is a large(1/4") and a small(<1/8") spade fitting.
the small one is positive, right? there is no + mark on the speaker.

Home receivers have a THD rating that shows how much distortion they have.
Is there any similar rating for car speakers to show how accurate they are?
If there isnt, what is a good way to select speakers, either in a store or online.
thanks

2007-01-17 06:48:48 · 4 answers · asked by brainiac 4

should i get 2 12" kicker L7's and 2 kicker zx 1000.1 amps or 2 jl 12w7 and 2 jl 1000/1 amps.

all opinions are welcome on other systems
thank you.

2007-01-17 05:25:02 · 10 answers · asked by Anonymous

probally going with some eclipse speakers

2007-01-17 03:23:04 · 12 answers · asked by VIC-RIDA 2

2007-01-17 03:20:43 · 3 answers · asked by DAVID a 2

I live in Warren, Michigan! Answer only if you know of places in Michigan, Thank You!

2007-01-17 02:01:50 · 4 answers · asked by *Dee * 1

Mitzu MIT-75 300 watts
Amp Features: High/flat/low pass filter built in. High/Low level input. RMS 150 watts x 2ch. Active crossover. Subwoofer network. Super bass system.

Subwoofer: Pioneer 600 watts

2007-01-16 21:35:37 · 7 answers · asked by badbob 1

2007-01-16 18:50:21 · 3 answers · asked by haus h 1

i have a 7 inch flipdown monitor and i want to install it in my tahoe, i'm not exactly sure how to do it. can anybody help me out?

2007-01-16 16:56:38 · 2 answers · asked by Jason M 1

looking for brain tuner for my clarion in dash t.v. the model is vrx925vd i will need that with the cables it is for a car.thanx

2007-01-16 16:16:41 · 1 answers · asked by marcos g 1

Simple question.

Which box is better for SPL??

-Sealed
-Ported
-Bandpass

and why???

2007-01-16 15:41:08 · 5 answers · asked by Anonymous

2007-01-16 15:18:26 · 2 answers · asked by Anonymous

i got a pontiac Aztec 2001 and my auto radio is lock how can i unlock it ???

2007-01-16 14:49:31 · 12 answers · asked by Anonymous

2007-01-16 14:32:13 · 6 answers · asked by ? 1

i have two amps a power acoustik 1920 2 channel plasa sphere amp and a 1600 watt 2 channel gothic series amp made by power acoustik and my subs are audiobahn 1251t 400rms and 800peak my question is how would i wire 3 subs to 2amps ? how would i wire the amp and the subs

2007-01-16 14:27:15 · 4 answers · asked by rex915 1

power for ur speakers in the the right ohm loaD?

2007-01-16 14:07:43 · 3 answers · asked by chris_estrada_281 1

I have 2 AudioBahn 10" Subwoofers, and together at 1800 watts Peak Power and 900 watts RMS Continuous Power . SO individually there 900 watts peak and 450 watts RMS. The Subwoofer is a 4 Ohm Single Voice Coil. Now I haven't bought an amp yet, but I found a 1000watt Nitro amplifier. It is a four channel amp at mono bridgeable and stable at 4 ohms heres the other Specification for the amp ONLY.
Number of Channels: 4
RMS Power (4 ohms): 40 watts x 4 chan
RMS Power (2 ohms): 75 watts x 4 chan.
RMS Power (1 ohm): Not Stable
Bridged RMS Power: 150 watts x 2 chan.
Peak Power Output: 1000 watts
Min. Impedance Unbridged: 2 ohms
Min. Impedance Bridged: 4 ohms
THD @ Rated RMS Power: 0.03%
Speaker Level Inputs: Yes
Amp Preamp Outputs: No
Built-in Crossover: HP (50Hz - 1kHz), LP (30 - 250Hz)
Bass Boost: 0 - 18 dB
Signal-to-Noise Ratio: 95 dB
Fan Cooled: No
Fuse Rating: 40A
Warranty: 1-year Manufacturer's

2007-01-16 11:20:43 · 3 answers · asked by Stephan 2

I want to install it myself to save money. How difficult will it be?

2007-01-16 10:47:05 · 4 answers · asked by Anonymous