Maintenance & Repairs - July 2006

My ex-boyfriend punched my front door, it is punched all the way through but there isn't a complete hole. Any suggestions on how to fix this without replacing the whole door? Here are some pics of the inside and outside of the door, they were taken with my camera phoen so the quality isn't that good. http://i15.photobucket.com/albums/a387/amandalt823/Door-Outside.jpg
http://i15.photobucket.com/albums/a387/amandalt823/Door-Inside.jpg

2006-07-27 08:28:54 · 17 answers · asked by Amanda T 3

The opener is a Stanley Quiet Glide Model UT605

2006-07-27 08:21:51 · 5 answers · asked by BUFFY43 1

I'm receiving , and I just pulled out my silverware and it has black stains. I need to clean it asap.

2006-07-27 08:06:45 · 4 answers · asked by Pascale 1

The first time we sealed our paver patio we used 'sweeping sand' to fill in the cracks, blew it off, and rolled the sealer on with a roller. This drug the sand out of the cracks and sealed it onto the surface of the bricks. We have tried power wahsing, but that also removes the top color layer of the brick leaving a black area.

2006-07-27 07:46:46 · 3 answers · asked by Jolee H 1

I know I can filter and reuse it but how do I finally get rid of the stuff. I want a 'green' answer.

2006-07-27 07:42:42 · 7 answers · asked by vancouverdew 3

I own a very old home and the old siding is that wide stuff that looks like compressed wood squeezed together to make about a 12 inch piece of siding. I am female, single and own my own home. I am not sure whether to have the old siding removed or how this all works. Any suggestions appreciated. I think vinyl would make my house nicer.

2006-07-27 07:32:49 · 3 answers · asked by happydawg 6

2006-07-27 07:31:14 · 5 answers · asked by Anonymous

2006-07-27 07:28:42 · 12 answers · asked by kkj459109 2

2006-07-27 07:20:53 · 7 answers · asked by TheOne 1

2006-07-27 07:05:50 · 10 answers · asked by Anonymous

2006-07-27 07:03:08 · 4 answers · asked by Anonymous

We have dealt with the manufacturer of the shingles, our contractor, City Building Inspectors, The new home warranty people even a lawyer, the installer of the shingles and yet we still have the problem. We even spent 9400 dollars to learn that our shingles we not installed properly the Ontario building code was not followed.

2006-07-27 06:18:42 · 3 answers · asked by shelby 1

the one that is on there now has four wires hooked up black red white and bare the new one only has three spots what do i do with the ground

2006-07-27 06:18:34 · 5 answers · asked by littleslix 1

2006-07-27 05:26:48 · 29 answers · asked by jp 2

2006-07-27 05:08:29 · 5 answers · asked by Anonymous

2006-07-27 04:28:58 · 4 answers · asked by ROY L 1

The water is turning green. We have cleaned the filter, cleaned the skimmer, and cleaned out the tank. But the PSI is rising. Will the PSI cause the tank to burst? We can't keep it below 22 right now. Does this make sense? Any suggestions? This is a public pool.

2006-07-27 04:22:03 · 2 answers · asked by Gothic Martha™ 6

ours is in a hall . the thermostat is set at 74 and the kitchen will read 80

2006-07-27 03:59:07 · 7 answers · asked by Steven 2

2006-07-27 03:46:05 · 5 answers · asked by kinny 2

I tried flushing it and got more dirty water. I'm not knowledgeable on plumbing or the like, so I really don't know what is going on.

2006-07-27 03:39:21 · 9 answers · asked by CLS 1

I changed the toilet flap ,about 1 year ago,now the flap dosn't want to seat flush,and causes it to slowly seep(on and off),and then drains alittle then refills the tank ,first I thought it was debri floating in the tank,any ideas why the flap wears out?or what may be the cause.

2006-07-27 03:37:02 · 7 answers · asked by Hawaiian Eye 1

the light in my kitchen was going out and I replaced both the 4 foot bulbs but they are still flicking and not as bright as they should be. Isn't there something in the middle works of the light I have to replace?

2006-07-27 03:33:03 · 6 answers · asked by WODYMAN 1

2006-07-27 02:58:59 · 3 answers · asked by Kibokho 1

2006-07-27 02:48:38 · 3 answers · asked by marcusandsylvie 2

Have ran in to this problem many times at my old employer, and the end result was always replacing that pricey unloader I would like to find out once and for all what go's wrong with these things.It's an xmv 3g30 ,3000psi,3400rpm,Honda engine WITH throdel.Thanks-scoot

2006-07-27 01:57:30 · 1 answers · asked by scoot 1

theyre getting bigger
how do i stop it from falling

2006-07-27 01:37:41 · 13 answers · asked by Pat 2

I donno, ask them if they fancy an afternoon of fun...

Is this a common thing lol.

2006-07-27 01:33:11 · 19 answers · asked by gorgeoushunk 2

2006-07-27 01:28:11 · 7 answers · asked by Dianne L 1

2006-07-27 00:36:59 · 11 answers · asked by Mad Harry Roberts 2

2006-07-26 20:36:55 · 16 answers · asked by mvb 1