Do It Yourself (DIY) - June 2006

2006-06-19 22:29:22 · 3 answers · asked by Anonymous

2006-06-19 20:57:44 · 12 answers · asked by doable_rods 5

I don't want to hire it done

2006-06-19 20:04:10 · 9 answers · asked by baloneycurtains 2

And to keep them out of my house we have tried everything

2006-06-19 17:15:52 · 40 answers · asked by mommy232005 2

2006-06-19 16:55:25 · 2 answers · asked by rick l 1

2006-06-19 16:19:18 · 8 answers · asked by pothead 1

Do-it-yourselfer with no current experience in tiling will tile a small bathroom floor (12 x 12 tiles).

2006-06-19 16:05:43 · 6 answers · asked by aroper1219 2

i have a 22" round charcoal bbq by webber. has anyone out there converted one of these into a little gas grill with lava rocks?

2006-06-19 14:08:22 · 8 answers · asked by Anonymous

I dumped the 2-cycle oil gas mix from the gas tank of the push mower. Changed spark plug. Cleaned air filter. Still will not run. What now? For some reason, if pump the safety release handle, it will run for about 3 minutes, if I keep pumping the handle. Then it dies. Did the 2-cycle oil gas mix clog up the carburator? Or is pumping the safety release handle indicating some other problem?

2006-06-19 13:30:47 · 11 answers · asked by ELIJAH 1

This question refers to British electrical standards.

2006-06-19 12:58:52 · 3 answers · asked by Robert G 2

2006-06-19 12:37:57 · 12 answers · asked by smaz_505 2

Can I cover the primer bulb with a plastic air tight lid, then pour gasoline in the carborator to start the push mower? Wil this keep the mower running?. Will the push mower run with out the air filter?

2006-06-19 12:25:22 · 11 answers · asked by Kinloch K 1

2006-06-19 11:52:37 · 3 answers · asked by TIGGER 1

But should I paint gloss or flat either way, I will have to prime, using reds and orange, for a modern look, should i paint one wall flat and the 3 other semi gloss?

2006-06-19 11:37:56 · 5 answers · asked by xcybergypsyx 2

2006-06-19 11:11:53 · 6 answers · asked by rjkoedel 1

i purchased an older brick home that did not have a unit put in it when it was built. and at this point and time it is better for me financially to purchase window units.

2006-06-19 10:31:48 · 5 answers · asked by mcollinsvcollins2003 1

The mdel is S3110 and a sticker says AD-993718 * Thanks so much if you can help.

2006-06-19 10:02:34 · 4 answers · asked by dane e 1

2006-06-19 09:52:53 · 17 answers · asked by Anonymous

I am thinking to install an attic fan becuase it is getting very hot in my attic.

PVC housing, $86
http://www.ventingdirect.com/productDetail.cfm?cPath=&productID=350

Aluminim housing, $256
http://www.ventingdirect.com/productDetail.cfm?cPath=&productID=N-RF68HRPSC&xView=

or
PVC but Solar Powered, $499
http://www.solarroofvent.com/Merchant2/merchant.mv?Screen=CTGY&Store_Code=001&Category_Code=SunRise1050

or
is there a better one that you know of?

The attic is 880 sq. ft.
I do have winter time here with 0F degree temps with snow.
I do not have trees above my house.
I do not have A/C.
I do use ceiling fans in the bed rooms.

2006-06-19 09:15:34 · 3 answers · asked by handydaddy 3

I haven't been making it to stay up all night.

2006-06-19 08:59:12 · 12 answers · asked by Anonymous

curve appeal

2006-06-19 08:25:49 · 14 answers · asked by sweetshanbell 1

please step by step or just give me a website

2006-06-19 07:53:03 · 12 answers · asked by consused dude 1

2006-06-19 07:37:24 · 11 answers · asked by Jack Tripper 3

2006-06-19 06:37:43 · 4 answers · asked by Nicolettep 1

more permanent but don't want the ink to run. Any suggestions?

2006-06-19 06:31:12 · 2 answers · asked by ? 5

2006-06-19 06:28:38 · 6 answers · asked by gecko68 1

2006-06-19 04:41:13 · 2 answers · asked by rut257 1

I don't want the deck attached to the house.

2006-06-19 04:18:30 · 6 answers · asked by Tigerladytwo 1

specifically, wedges for the frame install, closures for the cavity, straps to secure the door frame to the timber frame.? How to use all these different supplementary pieces.?

2006-06-19 04:12:44 · 0 answers · asked by MICHAEL P 1

Where can I get instructions?

2006-06-19 03:46:29 · 4 answers · asked by Anonymous