Ford

I usually wear my seatbelt but from time to time my job requires short drives due to multiple stops and I would like the beeping to stop.

2006-10-30 05:45:00 · 9 answers · asked by Cody 2

2006-10-30 05:37:23 · 3 answers · asked by Anonymous

can i replace it?
has this happen to anyone else?
any recalls

2006-10-30 02:41:36 · 4 answers · asked by Anonymous

witch one is better the amc or the ford

2006-10-30 01:06:49 · 17 answers · asked by gremlinboi55 2

I have just bought a ford puma and need to get a dog guard for it - does anyone know if Ford made one to fit the Puma, or if there are any you can recommend might fit?...;-)

2006-10-30 00:12:33 · 7 answers · asked by missy 2

the buttons on the door does not work what could be wrong

2006-10-29 19:19:56 · 4 answers · asked by Gwen B 1

2006-10-29 15:20:22 · 12 answers · asked by mustangman2590 1

2006-10-29 14:51:50 · 12 answers · asked by Anonymous

Is there any way to to wire a '95 E-150 for a trailer without splicing into the tail lights?

2006-10-29 12:23:54 · 4 answers · asked by IBBI 1

www.1968mustang.org My dad drove the damn thing off the show room floor. I believe I know what the car came with! OH, by the way they quit making the 289 in late 68!!

2006-10-29 12:14:55 · 6 answers · asked by B 3

I need to know were the pvc valve is on at 2001 ford ranger with the 4.0 shoc. i know it is usually in the valve cover some where but can't seem to locate.

Thanks for any help,
al1

2006-10-29 10:18:12 · 3 answers · asked by Albert L 1

2006-10-29 09:02:26 · 14 answers · asked by pedrojmaldonado 1

I have a '99 Ford Expedition Eddie Bauer with a 5.4L engine and the 4R100 Tranny. But I don't know the horsepower rating.

2006-10-29 05:25:41 · 5 answers · asked by fellin1975 2

2006-10-29 05:03:18 · 6 answers · asked by Timothy W 1

is any one selling one ??

2006-10-29 05:02:48 · 4 answers · asked by cosworthrep 1

i want to buy a Ford mustang and modify the engine with performance parts, etc. i heard somewhere that the '89-'91 are good to modify because of the engine parts are forged, not cast or something like that. is this true? please clarify.

2006-10-29 04:31:59 · 5 answers · asked by mjmustang5 2

do you think it would give me alot more then a 100k miles?

2006-10-29 03:53:35 · 8 answers · asked by emad t 1

2000 Escort ZX2 - what's the trick to getting the pins out of the caliper? I can get the caliper off, get the disc off, remove the springs, and compress the piston, I just can't get the pins out. They're pretty crusty. I tried vice grips but can't grab it anywhere. I tried a punch and hammer but they don't budge.

2006-10-29 02:26:22 · 2 answers · asked by Jim C 5

i've been having trouble with the starter disengaging after a couple of cranks and thought it might be the hold in system, it tested ok with the starter out, no load the way it says to test in hd manual. i was looking at the overrunning clutch to see how that was working and the inside seemed to be real wet and gritty and there was no 'o'ring in the housing. when i held the big gear in my hand and turned the shaft like i would be cranking the motor and then turned the other way to get the clutch to freewheel it would be stuck and take alot of force to get it to freewheel, is this thing broken and how do i get one of these 'o'rings i can't find them in any catalog?

2006-10-29 01:54:28 · 2 answers · asked by Anonymous

2006-10-29 01:04:53 · 7 answers · asked by manuelito b 2

We replaced an idler pulley and now are unable to put the serpentine belt back on. We have found the tensioner pulley but cannot budge the bolt. Any help will be appreciated.

2006-10-28 19:53:09 · 11 answers · asked by sjborem 1

2006-10-28 18:39:46 · 6 answers · asked by trick_master50 2

2006-10-28 17:17:04 · 15 answers · asked by David S 1

2006-10-28 17:15:20 · 3 answers · asked by David S 1

2006-10-28 16:57:01 · 13 answers · asked by mustangman2590 1

2006-10-28 16:09:53 · 4 answers · asked by tomstanfill 1

the motor is a ford explorer 2000reg northface model.warning lights on dash which have been affected ar, abs,suspension,airbag and engine management. car starts and drives

2006-10-28 15:11:15 · 3 answers · asked by sinna 1

2006-10-28 14:10:01 · 8 answers · asked by Anonymous

Okay...so My 2002 ford taurus ran out of gas. the gas gauge hasnt been working. It ran out. So I went and got more gas. Now it will not start. It tries to start. Do you think it is the fuel pump or injectors? It is an electrical pump. Did I really screw it up now??? Please help!!!

2006-10-28 11:27:58 · 11 answers · asked by Miriah 3

2006-10-28 09:18:47 · 5 answers · asked by kulstation 1