Engineering - April 2007

2007-04-21 03:51:18 · 3 answers · asked by moonbeam_2000g 2

Hello all
Does anybody know of some hardware and/or software that will let me control a number of liquid valves and sense temperatures with probes away from the PC. I'm sure that there must be something out there somewhere???
I've done the usuall googleing but with no luck.
Thanks In Advance Rich

2007-04-21 02:42:41 · 5 answers · asked by cheeseypeas 2

Please also list both advantages and disadvantages for both aeronautical engineering and pilot. please mention their monthly salaries too.

2007-04-21 02:15:48 · 6 answers · asked by Arpit Roy 2

2007-04-21 01:31:43 · 6 answers · asked by dave ry 1

In a pipe flow, there is an orifice meter and pitot tube attached to the pipe to measure the flow rate. I have the graph of mass flow rate(m) vs manometer reading(h) on log-log paper. This is y= log m vs x= log h What information can i obtain from the slope and the intercept

2007-04-20 22:28:38 · 3 answers · asked by zerald 1

2007-04-20 19:26:03 · 2 answers · asked by Anonymous

2007-04-20 17:57:07 · 7 answers · asked by Zack 1

Why the Steel structures of the WTC towers dissaperar or evaporated like by magical?
& Why the Main Stream media rejects all Consopiracy Theories that involves Israel? http://wtc.nist.gov/pubs/factsheets/faqs...

Jet fuel burns at 800° to 1500°F, not hot enough to melt steel (2750°F). However, experts agree that for the towers to collapse, their steel frames didn't need to melt, they just had to lose some of their structural strength--and that required exposure to much less heat. "I have never seen melted steel in a building fire," says retired New York deputy fire chief Vincent Dunn, author of The Collapse Of Burning Buildings: A Guide To Fireground Safety. "But I've seen a lot of twisted, warped, bent and sagging steel. What happens is that the steel tries to expand at both ends, but when it can no longer expand, it sags and the surrounding concrete cracks."
"Steel loses about 50 percent of its strength at 1100°F,
What secret material was used in the demolition?

2007-04-20 16:10:18 · 5 answers · asked by Rikjard M 2

my guestion is . there is a voltage slector on the rear of the pump witch setting would i use 115 volt setting or 230 volt

2007-04-20 14:25:37 · 8 answers · asked by Anonymous

2007-04-20 14:24:06 · 1 answers · asked by packman 1

I have a report due on Monday and i have to have a slogan for a use of a domestic battery in the 1950s

I hope you can answer my question
Thanks!

2007-04-20 14:04:09 · 4 answers · asked by ..... 2

just wondering

2007-04-20 12:56:15 · 5 answers · asked by macgyver 1

please help i need help on a project & am completly lost need information A.S.A.P

2007-04-20 12:53:56 · 3 answers · asked by Lea 1

2007-04-20 12:23:21 · 4 answers · asked by Jean Marc P 1

I want to wire it to a 20 amp circult can i and witch voltage do i choose 230 or 115 or the rear of the mottor?

2007-04-20 12:20:50 · 5 answers · asked by Anonymous

are they just semi conductors like transistors ,intigrated chips, and diodes

2007-04-20 10:55:43 · 4 answers · asked by macgyver 1

to increase vertical distance I mean.

2007-04-20 10:49:41 · 4 answers · asked by z3po 5

I would like to either buy one or a ready to essemble kit . How big of a windmill would I need to provide enough electricity for a 7 room house with full basement. I want to use it to provide all the power including heat in the winter.

2007-04-20 10:37:56 · 6 answers · asked by mjorod 4

I am looking for a material that blocks the visible spectrum but lets IR light through with little problem. Preferably a film or some kind of easily obtainable plastic. Thanks!

2007-04-20 10:37:49 · 7 answers · asked by Off the Grid 1

2007-04-20 10:30:57 · 2 answers · asked by DA BOSS OF MAC DRE 1

Does any body know good websites for image processing, such as image segmentation, morphology, fourier transform and such.
I need a website or something that explains it in detail, cause I have an image processing course and I don't understand anything.
Any help is appreciated, Thanks.

2007-04-20 08:38:32 · 2 answers · asked by sina 1

When refering to quality management, does PDCA (Plan, Do, Check, Act) describes the basic logic for data-driven continuous process improvement?

2007-04-20 08:34:37 · 1 answers · asked by Anonymous

My electronic teacher asked me to bring him a pic of a IC741,can anyone help me??PLZ

2007-04-20 08:08:33 · 3 answers · asked by Mehrania 2

2007-04-20 07:55:21 · 2 answers · asked by Anonymous

i need the detailed construction of the tunnel diode
with VI charactristics
please give me contact details whoever gives the answer for the qustion

2007-04-20 06:50:38 · 2 answers · asked by abhijit u 1

We are installing a 1000KVA diesel gen set near our satalite communication receiver . Whether the satalite communication system shall have any effect from the electromagnatic fields generated from the generator.

2007-04-20 06:44:58 · 3 answers · asked by pravs 1

Thank you for answering my question.
My problem is that I have a Logic IC that it's name and IC number is fully cleaned & I did'nt know any think about it.
By analysing the circuit that this IC used in it, I had determined its VCC & GND but I need to determine it fully.
I want only a way for determinig its pin (input or output).
Then I can find its truth table for every output by letting different input valuations to it and processing its response by an AVR.

Can you help me?
please place your mail here or mail me your answer if you want, then I can explain you more details of problem and ...

My email:
magnesium_1987@yahoo.com

2007-04-20 04:24:58 · 3 answers · asked by Anonymous

2007-04-20 04:17:44 · 2 answers · asked by laura m 1

Do electrical engineers get to travel around the United States with their travel expenses covered by their employer?

2007-04-20 04:02:12 · 7 answers · asked by clove88 2

i would like to know the path way of becoming a weapon engineer
i heard that it start from getting a degree in systems engineering
is that true
if u plz provide me with extra info on the topic

2007-04-20 02:02:37 · 1 answers · asked by smearenstien 1