English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

Engineering - July 2006

[Selected]: All categories Science & Mathematics Engineering

this filter should be no corrosion effect on down stream of filter and it must remove water very well.

2006-07-31 22:34:50 · 4 answers · asked by Shahrzad T 1

i am doing B.E. and she is in school.her brother is my best freind.

2006-07-31 22:16:24 · 16 answers · asked by Anonymous

Is the following statement true or false:
"when clutch is used engine diengages from the vehicle then load on the engine decreases .
but to prevent the exhaust gases in the cylinder coming back to the suction line rich mixture of fuel is to be supplied so fuel consumption increases"

2006-07-31 20:38:55 · 9 answers · asked by Anonymous

Since a center tapped has two output, i wonder the 1:50CT stated in the spec sheet actually means the whole winding or divided equally for each tap?

2006-07-31 19:41:40 · 2 answers · asked by Walker 1

From the schematic point of view, some transistors are one sided (primary only). What's the point in that? Isn't the secondary part (stepped up or down) the output that we are looking for?

In this case there is no secondary. Pin wise, it's either 2 pins or 3 pins (for CT type)

2006-07-31 19:38:40 · 4 answers · asked by Walker 1

hello frnds..i am into my last year in engg. i require a major project in electronics..i require some schematics or any good links anyone can offer..thank u any effort is appreciated..looking forward 2 ur replies..

2006-07-31 18:56:04 · 5 answers · asked by free_soul_of_17 2

why we dont use electronic field for imaging of body tissues?
imagine the body between two parallel metal plane,it makes an electronic condenser and the body works
as a dielectric for this condenser,every tissue has itself dielectric constant,and these planes are formationed
by very small metal squares,so by rotating these planes around the patient,we can calculate the constant of every
tissue and find out which tissue it is,it works better than X-ray radiography and even MRI

2006-07-31 18:51:07 · 5 answers · asked by mosi 1

especially E.E............

2006-07-31 16:50:45 · 12 answers · asked by The Apostle 2

Please comment with a scientific answer...

2006-07-31 14:50:09 · 9 answers · asked by dankees98 2

I'm confuse. Do you use mathimatical on both or one?

2006-07-31 14:48:12 · 6 answers · asked by Mattman 6

2006-07-31 13:12:05 · 7 answers · asked by sta762002 2

is it possible to introduce some chemical (whether its a gas,solid,liquid) into a photovoltaic cell to increase its efficency and increase its load capability

2006-07-31 12:44:12 · 1 answers · asked by captkirk 2

Are there any good small motors that are quiet but powerful enough to move a lot of air? Is there a better way to move air then with a fan? This is for a project I am doing; the motor or other contraption should be the same size or smaller than the size of an average electric shaver, in other words, not too big.

2006-07-31 11:45:09 · 6 answers · asked by rolshmin267 2

Does anyone know how to make an Air Conditioner out of a compressor and a waste oil heater and other sundry parts?

2006-07-31 11:23:25 · 2 answers · asked by Foundryman 2

the 100w dosnt put out egnof light. i have a total of 2000 watts in my living room 25 lamps can you help
?

2006-07-31 10:46:44 · 7 answers · asked by ziggy420 2

Hi everyone, I need some help with designing a container for an egg - it is not for an egg drop, it is just pure aesthetic design, I was thinking of how once the egg is placed in the container it can activate a light or a tripod? Any ideas? THANKS

2006-07-31 10:14:40 · 5 answers · asked by Suzy R 1

I always thought there were seven simply because "Seven Simple Machines" sound familiar.

2006-07-31 09:18:57 · 11 answers · asked by butnozzle 2

Exactly. I mean the screw threads on a bolt or screw-top jar. When was it invented, by whom?

2006-07-31 08:53:54 · 15 answers · asked by syrious 5

Im working on an at home project to supply someone with a constant air supply under water. does anyone know how many PSI of air pressure is needed to pump air per foot of water.

2006-07-31 07:37:28 · 8 answers · asked by cronos51101 5

Electrical power and its tranmisson

2006-07-31 07:32:43 · 2 answers · asked by goring 6

where people discuss the inventions and projects they are working on.

more things that people want to share and get help on their ideas rather than ones that are secret because they want to make a fortune on them.

thanks

2006-07-31 07:08:23 · 1 answers · asked by brainiac 4

All information about this subject

2006-07-31 07:04:12 · 4 answers · asked by Anonymous

2006-07-31 06:26:52 · 6 answers · asked by No1HdweLady 1

2006-07-31 06:05:54 · 1 answers · asked by negro_eh 1

I don't think that the radiations may cause fire threat. This instruction is written not only on fuel stations but also in nokia handset manuals.

2006-07-31 05:49:47 · 16 answers · asked by stroha 2

I work in a customed sheet metal fabricating shop and recently some of our customers have been bought out by a German company. Now all their prints are opposite in regards to views. In the origional prints the center drawing was the face and the drawing on the right was of the right side of the part, but on these new prints it is the left side of the part. It is very confusing to the guys out in the shop. Why do they go at it like this when our way seems to make more sense? Am I nuts?

2006-07-31 03:20:33 · 8 answers · asked by thebuffettour 2

2006-07-31 03:15:01 · 4 answers · asked by FourHead 2

fedest.com, questions and answers