Engineering - December 2006

to replace engine with a pneumatic drill which runs on compressed air.and the air stored in a cylinder at high pressure

2006-12-22 17:50:36 · 5 answers · asked by ROBUSTMAN 2

2006-12-22 17:32:27 · 3 answers · asked by ROBUSTMAN 2

I am doing a science project that requires a sound level meter (which i have) and a frequency maker (its a thing that is programmed to create sound waves) which i haven't bought. where do they sell them??? in california, LA, Torrance, or Long Beach, pleez!

2006-12-22 17:07:23 · 3 answers · asked by DBSG/SS501_fan 2

My son will be passing out of Xth Standard in 2007. At present he is studying in a residential school at Ahmedabad. He wants to pursue Engineering and for this he will have to get coaching for Entrance Exams. I wanted some good reference for coaching of IITJEE, GUJCET, AIEEE etc.

2006-12-22 16:46:49 · 2 answers · asked by indralok90 1

I ame building a solar oven and I am using a real oven but I dont know how manny watt solar panel I need.

2006-12-22 16:42:00 · 7 answers · asked by ducks fan 1

I am looking for a common material that is heat resistant and non-conductive.......any ideas?

2006-12-22 15:27:07 · 16 answers · asked by Che 2

I would like to simulate FEA of spherical dome when subjected to wind and snow loading in NASTRAN but do not know how to do it. Can anybody help me? I used to use axisymmetric element in NASTRAN to do internal pressure and self weight analysis but I dont know how to model the dome using axisymmetric element when it is subjected to wind and snow loading. I have no idea which type of load should be chosen in doing this analysis. Thanks in advance.

2006-12-22 15:17:37 · 2 answers · asked by ck 1

I am building a magnetic compressed engine that will run a poll reverse gate in the cylinders that can allow the adjustment of reverse poll magnetic compression with a electric acelerator module to change the revolutions of the motor .Can any one help myself with suggestions of light materials such as alloys that need too adapt too wear in the engine as heat stress is no factor in this motor.

2006-12-22 14:51:19 · 4 answers · asked by Anonymous

I am in high school and I was wondering if I should pursure this career.I would also like to know the universities that offer the best programs.Also, are there many females in this area of engineering?

2006-12-22 13:26:08 · 7 answers · asked by jaja 1

2006-12-22 13:18:08 · 7 answers · asked by JoJo 1

Appreciate any info about a multiplexer that could be used to control a high current (up to 5Amps) circuit. Most Muxs in mouser and digikey are in mA.
Thanks in advance for your answer.

2006-12-22 13:16:39 · 1 answers · asked by Anonymous

The electric motor is a Marbel....without it we might be as far back as the horse driven bugy...why do we not know who invented the electric motor?

2006-12-22 09:41:16 · 6 answers · asked by rene_rosecity_portland 1

2006-12-22 09:17:41 · 7 answers · asked by kedi 2

2006-12-22 08:49:41 · 10 answers · asked by Jeanette S 1

Anybody knows how much and can tell me why??
Thanks!;)

2006-12-22 07:57:35 · 4 answers · asked by falcidia 4

Is there anyway to reduce the angle of emmission in the up and down direction? For example, in the side to side emmission, yagi antennae's can reduce the angle to about 20 degrees in the side to side way. I'm not talking about polarization, but the spread of the waves.

Thanks.

2006-12-22 07:41:46 · 3 answers · asked by Ilooklikemyavatar..exactly 3

I have looked on the ASM's website, and that hasn't been helpful at all. I have searched on the internet, through various search engines, and I still haven't found anyone.

2006-12-22 07:10:56 · 3 answers · asked by Anonymous

I would like to wire up a bi color 3 pole LED in my car to indicate when my compressor is running and when it isn't. I would like to use a DPST relay with this. Any help out there? I am a novice/amateur with some electrical knowledge.

2006-12-22 06:24:18 · 1 answers · asked by Anonymous

2006-12-22 06:11:34 · 12 answers · asked by putter 1

2006-12-22 06:03:21 · 9 answers · asked by Boboso 1

2006-12-22 04:55:54 · 11 answers · asked by Anonymous

Do I need a Garth Brooks CD?

2006-12-22 04:32:10 · 2 answers · asked by Anonymous

2006-12-22 04:21:29 · 5 answers · asked by Heretostay 1

All about industrial mechanical maintenance engineering. This trade is significantly applicable to millwrights activities. Any country is ok provided you find me what I am interested to pursue my Bachelor's degree in the field of Millwright technology.

2006-12-22 04:15:06 · 2 answers · asked by Millwright 1

2006-12-22 04:09:02 · 13 answers · asked by mansooresbi 1

I am building a small EV and have up to 26 amps @ 38.4 vdc (theorectically). I was trying to find an enexpensive way to separate the multiple 9.6vdc NIMH battery packs to facilitate charging.

2006-12-22 04:06:22 · 7 answers · asked by bronsonj 1

2006-12-22 03:19:51 · 10 answers · asked by beto 1

Is there a published ASTM testing method for a "Vibration Analysis" ?

2006-12-22 03:15:53 · 3 answers · asked by Greg Fitz 1

2006-12-22 03:10:30 · 3 answers · asked by jerck 1

how much cost and course duration

2006-12-22 02:46:41 · 5 answers · asked by jeya r 1