Ford

has anyone had to remove the baffel where you pour the oil on the drivers side so the rockers will clear.,its a plate under the cover.

2007-01-30 14:38:57 · 5 answers · asked by slick 50 1

I just want to know if anyone has some info on it.
ive been informed but i dont know if its true.

2007-01-30 13:50:14 · 12 answers · asked by Anonymous

My 4 wheel drive selection seems to either half enqauge or stick in a position.

Is it the Electronic outer module by the Trans case that is causing this?

2007-01-30 13:22:48 · 6 answers · asked by oe542 2

I want to take out my console in my truck and put in a bench seat I would like to know what I would need to do to do so and where to go to do it.

2007-01-30 13:19:52 · 3 answers · asked by Anonymous

i have an o2 ford ranger i just put led bulbs in the back and it blinks really fast whats wrong and be for i put them in some times my blinkers would work and some times they dont do i need a new switch?

2007-01-30 13:16:24 · 3 answers · asked by dustin s 2

where is the vacuum modulator located on a 1991 caprice classic?

2007-01-30 12:54:50 · 6 answers · asked by ALBERTA G 1

acn some one help me with this my 1989 mustang will not stay crank when i jiggle the wires under the dizzy i can here a funny noise from over by the coil its like a slight whining or staticy sound has anyone experienced this before, but its the wires form the dizzy part #8579

2007-01-30 12:26:35 · 2 answers · asked by slick 50 1

Is $2500 a good deal on a 1971 Ford LTD 4 door, it has a rebuilt 429 2 barrel V8 (which came from the factory), C6 transmission, air conditioning (still blows cold), runs/drives great, little rust on the usual areas, body/interior is in very good shape.

2007-01-30 08:52:28 · 11 answers · asked by Fell In Love 7

How do I install it myself? What tools do I need?

2007-01-30 06:50:15 · 1 answers · asked by rob1963man 5

2007-01-30 05:30:13 · 6 answers · asked by Tammy l 1

2007-01-30 03:05:01 · 10 answers · asked by Jman 1

2007-01-30 01:45:43 · 19 answers · asked by BTH L 2

2007-01-29 17:35:08 · 2 answers · asked by Tomas C 1

i just bought it

2007-01-29 14:39:52 · 14 answers · asked by ms. clean 2

2007-01-29 14:34:01 · 11 answers · asked by Robbie W 2

Anyone know how to remove the plastic trim covering the inside of the back door. Once off I can replace the rear winscreen wiper unit. I have a Ford Explorer 1999.

2007-01-29 14:29:01 · 2 answers · asked by staple 1

The 90's models to be precise. I am wondering if I can just drop the Crown Vic engine out and put it in my mustang. All answers are appreciated.

2007-01-29 14:18:06 · 8 answers · asked by Metal 4

i lost the only ignition key to my 1990 Ford F150. I looked into the manual and they said to bring it to a shop were they will need to dismantel the column to replace it. i would be fine with putting a three way switch in its place (a switch that position one is off, two is running, and three is for the starter(spring loaded)). i have no idea were to start.

2007-01-29 14:13:44 · 7 answers · asked by rickblansett 1

The dealership says that they cannot get parts for that old of a model. Any suggestions? I tried googling.

2007-01-29 13:59:01 · 3 answers · asked by Kendra Z 2

need to know what numbers go with horn fuse&relay

2007-01-29 13:37:40 · 5 answers · asked by Anonymous

I really do not know what was wrong with my ad?

2007-01-29 13:20:29 · 3 answers · asked by Ron 1

Engine is stalling on 1996 Ford Probe GT, while driving on highway at 100km or even now in city? What is causing this?

2007-01-29 13:17:46 · 7 answers · asked by DThom 1

2007-01-29 12:55:58 · 9 answers · asked by FELLOW CRAFT 2

My heater in my 1997 Ford Aspire is very weak . When the car is not moving it heats up well . But as soon as i start driving it gets Luke warm . Very hard to see when the windows keep fogging over . Please help!!

2007-01-29 12:17:35 · 10 answers · asked by Anonymous

ford Escort - 1997 - 1.6i 16v. Bought as a good car but it just seems to fall apart at the wrong time. It's due it's MOT mid Feb or so but it needs work and badly. I want to keep this car as it will be cheaper in the long run for now than a new car. Sitting with over 100k+ miles on the clock, does miles travelling up and down between Edinb and Dundee a lot. Needs clutch replaced, exhaust looked at, new brake pads for now. Can anyone suggest where to start (no i'm not just binning it, Fords are meant to be cheap and easy to repair and run) or who to take it to to have it looked at etc.

2007-01-29 12:16:00 · 9 answers · asked by Anonymous

with a couple bolt on parts and a 150 shot of nos

2007-01-29 12:01:40 · 5 answers · asked by Tammy l 1

I have a 97 Ford Explorer and it blows out cold air. I've changed the thermostat and flushed all the hoses, radiator, as well as the hoses to the heater core. There seems to be some type of valve located just before the hoses that go through the firewall to the heater core that opens and closes when the heat is turned on and off; I checked that and it’s working fine. I've also checked the water pump weep hole for leakage and it doesn’t seem to be leaking at all. The only thing I can think of is the heater control itself, because the temperature doesn’t change at all, when I move the dial from hot to cold. Has anyone had any similar problems, or have an idea as to what it could be?

2007-01-29 11:37:45 · 8 answers · asked by nick s 1

my 66 ford mustang just had the valves adjusted and now the car seems to be alot slower, and it chokes up when it gets above 4800 rpm. it used to go to 6500 rpm. could the valves be too tight? any suggestions would be helpful.

2007-01-29 11:16:41 · 8 answers · asked by girlbld 1

2007-01-29 10:53:01 · 3 answers · asked by big2na1377 1

Ford pickups

2007-01-29 10:47:33 · 11 answers · asked by Zach Y 1