Engineering - February 2007

2007-02-18 07:25:46 · 3 answers · asked by Anonymous

Occustat

2007-02-18 07:22:15 · 3 answers · asked by Anonymous

2007-02-18 07:16:03 · 4 answers · asked by kachilous_2002 1

tried to figure how to do this by either using step up and down transformers. or even if there would be someway close to getting ? amps one direction without loosing volts. overhead only.

2007-02-18 07:15:36 · 1 answers · asked by mouse 1

I am stuck on a problem with a simple electrical circuit. (I am studying independently, and so I'm not trying to cheat on a homework). The problem is sort of shaped like this: [-]. It has a 2.0 volt battery at the top with an internal resistance of 1 ohm. It has a 1.0 volt battery at the bottom with an internal resistance of 2 ohms. And across the middle (parallel to both batteries and also in between them) is a resistor of 2 ohms. I need to find the current across the 2 ohm resistor. I know the answer to be 0.42 amps, but I have know idea how to get it. Please can you help?

2007-02-18 06:52:48 · 7 answers · asked by eazylee369 4

details abt the harmonic orders......

2007-02-18 06:34:56 · 6 answers · asked by Anonymous

Could someone tell me where to find partial linear differential equations exercises (problem and solution); I'm specially interested in solving the typical steady state temperature in a cilinder with different bundary condditions; any hel will be appreciated

Thanks

2007-02-18 06:16:24 · 1 answers · asked by Anonymous

2007-02-18 06:11:09 · 2 answers · asked by Jaysson B 1

HI
I LOOKING FOR A THSES OR ARTICLE ABOUT HOW DO I CONVERT A CONTROL SYSTEM TO ELECTRONIC CIRCUIT ?

2007-02-18 05:31:08 · 4 answers · asked by seyyedkh 1

The clock has two places to wind one clockwise the other counter clockwise

2007-02-18 05:24:41 · 1 answers · asked by mary&ronnie d 2

i made this model of a hot air balloon. i know the perimeter of each shape i used because i carefully drafted the shapes i used. but i want to know how i can calculate the volume, so i can find out how much air it can hold. i want to know if there is a certain formula that you use. thanks and honest answers plz!!!!!!!!!!!!!!!!!!!!!!!

2007-02-18 04:52:30 · 7 answers · asked by *believe_it* 4

2007-02-18 04:41:03 · 4 answers · asked by pie 1

2007-02-18 04:37:36 · 4 answers · asked by a.j_cipan 1

2007-02-18 04:32:21 · 3 answers · asked by sudharshan n 1

2007-02-18 04:27:18 · 4 answers · asked by a.j_cipan 1

I'm not an engineer but a communications major. I work for a state power transmission company in the philippines. I'm trying to compare our region's total substation capacity (which they say is big) to the consumption of other smaller countries. in this case, its 6,587.2MW. I hope you can help me verify. thanks in advance!

2007-02-18 03:55:39 · 1 answers · asked by rcsandovaljr 1

2007-02-18 03:31:23 · 9 answers · asked by Anonymous

2007-02-18 03:30:28 · 6 answers · asked by Anonymous

2007-02-18 03:18:23 · 1 answers · asked by mary&ronnie d 2

I'm trying to convert because I want to compare our 6,587,200 (6587.2MW) substation capacity in terms of the power consumption of other areas/countries. Im not an engineer btw.

2007-02-18 02:44:21 · 4 answers · asked by rcsandovaljr 1

are we expected to believe that the steel in the twin towers on September 11th 2001 melted so quickly that Tower 2 only survived for 38 minutes and Tower 1 survived for 1 hour and 20 minutes.

2007-02-18 02:36:51 · 12 answers · asked by 911 Truth 1

2007-02-18 02:14:40 · 4 answers · asked by mehdi sharifi sedeh 1

plz dont answer the question with jokes...............iam waiting for an good and sincere answer

2007-02-18 02:11:00 · 3 answers · asked by arun bose 1

2007-02-18 01:54:23 · 1 answers · asked by Jaysson B 1

2007-02-18 01:49:22 · 1 answers · asked by Anonymous

2007-02-18 01:23:02 · 5 answers · asked by Anonymous

What are some common uses for Magnets in everyday life?

2007-02-18 01:18:53 · 15 answers · asked by ThisMan 3

2007-02-18 00:36:50 · 1 answers · asked by Neeraja Singh 3

Hi ....

I am engineering student and I want Smoke Detector Circuit diagram and information about it from which i can make project.

2007-02-17 23:41:41 · 3 answers · asked by Anonymous

2007-02-17 23:29:34 · 4 answers · asked by Nandita S 1