Engineering - November 2006

2006-11-29 04:48:10 · 8 answers · asked by Anonymous

2006-11-29 04:37:39 · 7 answers · asked by ASHERS 1

2006-11-29 04:10:02 · 8 answers · asked by boy boy 7

I'm looking for symbols for resistor, capacitors, coils, switches, transistors, diodes, etc.

2006-11-29 04:09:27 · 2 answers · asked by wisdom tooth 3

signal/noise

2006-11-29 04:00:02 · 1 answers · asked by JAMES 4

2006-11-29 03:43:21 · 2 answers · asked by Anonymous

2006-11-29 03:13:25 · 6 answers · asked by tender2 1

Does eigenvalue analysis=modal analysis? Does eigenfrequency=natural frequency? What is eigenvalue?

Does eigenvalue analysis=modal analysis? Does eigenfrequency=natural frequency? What is eigenvalue, eigenvectors, eigensystems?
Please explain what is the definition or what you understand by each term? List out their differences and similarities. Please bring in relevant concepts if needed!

2006-11-29 03:06:18 · 5 answers · asked by Anonymous

I'm trying to convert a hand crank meat grinder into an electric one. I know that the motor and grinder need to be connected by 2 pulleys and a wheel. The motor I have is 1/3 HP, 3450 rpms and comes from a dishwasher. There is some kind of coil in the wiring before the current gets to the motor. Do I need this coil/capacitor for the motor to work or can I just splice the motor to an electric cord and add an on/off switch? I just want to make an electric meat grinder and want to know how to properly make the motor turn.

2006-11-29 02:51:59 · 5 answers · asked by paul67337 7

and how do they work?

2006-11-29 02:44:03 · 4 answers · asked by Fiesty Redhead 2

2006-11-29 02:41:59 · 1 answers · asked by earnmoney u 1

Assuning a source Voltge of 0.8V, Determing the curretn in a 50mW LED(Light emitting diode)

If anyone can solve this, can you please explain any formula used to solve alonge with the answer?
THank you

2006-11-29 01:47:32 · 4 answers · asked by jeep10455 2

Please provide sources if possible

2006-11-29 01:12:14 · 1 answers · asked by spam_and_junk_mail 2

drum 200 lit of capacity filled upto 170 liters
to heat hydraulic oil mix with water, what is the capacity of heater to reach temp 90 degre within 30 minute.
water content in in hydraulic oil may be 2 to 20 litre
purpuse is to remove water from hydraulic oil.

2006-11-29 00:51:23 · 2 answers · asked by shaikh g 1

2006-11-29 00:24:12 · 4 answers · asked by googlefan 1

2006-11-29 00:21:27 · 6 answers · asked by boy boy 7

2006-11-28 23:36:26 · 6 answers · asked by raju p 1

2006-11-28 23:21:59 · 6 answers · asked by devanathan d 1

2006-11-28 23:16:58 · 6 answers · asked by devanathan d 1

2006-11-28 23:13:45 · 7 answers · asked by tom_1106 1

2006-11-28 22:56:11 · 7 answers · asked by lizathebest2004 1

2006-11-28 22:51:31 · 3 answers · asked by lizathebest2004 1

2006-11-28 22:42:48 · 5 answers · asked by rajesh k 1

2006-11-28 20:41:58 · 7 answers · asked by cdmisst 1

I do not wnat off-the-textbook answers, auch as "no back emf" et. all. Please explain as you would to a layman.

2006-11-28 19:09:59 · 7 answers · asked by Anonymous

2006-11-28 19:06:18 · 2 answers · asked by Anonymous

2006-11-28 19:05:04 · 3 answers · asked by Yamuna 1

what is the answer to this integral? int(0, 2pi/1000) 144cos^2(1000t) dt?

2006-11-28 18:58:53 · 1 answers · asked by kwikemartemployee 2

Could a grapple gun pull at least 200 pounds like in the movies?

2006-11-28 18:30:09 · 4 answers · asked by credlec 1

2006-11-28 17:58:53 · 6 answers · asked by IA 1