Car Audio

i need to buy my 1st pair of componets ..and wanna make it my last.can ne one tell me best 61/2" comps till 300$..and do ne body kno ,smthin bout hertz comps

2007-03-25 10:00:48 · 7 answers · asked by aman gujral 5

I was wondering if supplying subwoofers with not enough power will actually damage the subwoofer or if it will just not sound good or hit very hard.

I heard supplying subs with too much power is better than not enough, but will it actually hurt the subs to supply them with too little power?

2007-03-25 09:08:48 · 10 answers · asked by kurtfizzle 2

I have a Sony amp pushing my subs, I just recently added a pair of 6x9 and 4x7 to my setup and it sounds great when I turn the key to ACC, but when I start the truck the speakers I just put in put out a humming/whinning sound. I ran seperate Battery and ground lines and I bridged the remote power together. I just cant figure it out.

2007-03-25 08:09:41 · 11 answers · asked by David W_ Master-Op 2

http://www.bestbuy.com/site/olspage.jsp?skuId=999950600050001&type=product&id=pcmprd50800050001


and could sum1 explain this Continuous Watts per Channel (4 Ohms) 300 x 1







Continuous Watts per Channel (2 Ohms) 500 x 1







Max Power Watts per Channel (4 Ohms) 300







Max Power Watts per Channel (2 Ohms) 500







Max Power Watts per Channel (4 Ohms Bridged) 1000

what does all that mean? i know nothing about this stuff so explain good please
? and is this combo any good?

2007-03-25 07:51:32 · 5 answers · asked by genius 2

I'm looking for one of those stereos that can come out and then up and form a screen kind of like navigation, except without navigation. Does that make sense? Im trying to explain it the best I can :) What are those called and what brand typically makes the best ones? It's going on a '97 BMW 318i, if that helps. Thanks!

2007-03-25 06:59:21 · 5 answers · asked by Kayla-Ann 3

ok i have a pioneer head unit it is a 6800 mp model and i have everything hooked up right but my remote control will not work for it i have the battery in it and everything

2007-03-25 06:42:54 · 2 answers · asked by Zach C 1

I have two 400 watt kicker subs and i have a 400 watt kicker amp and i was wondering if it would work if i run both speakers through the same port

2007-03-25 06:00:24 · 7 answers · asked by Russell 2

Do I require more power in a sealed enclosure or should I go less? And how much more or less? Lets say I'm running a 500 watt subwoofer sealed, what power should I give it?

2007-03-25 05:42:58 · 4 answers · asked by Life Is Illusive 3

How Can i find my speaker wires in my 97 mercury tracer? or what color are the wires for each speaker, i want to hook up a different radio and i need to find out what wires go to what speaker.

2007-03-25 05:34:58 · 4 answers · asked by Anonymous

2007-03-25 05:30:15 · 8 answers · asked by KEWLBOY 2

I recently purcahsed a new sony radio and had the electronic store install it in a Honda Accord. Five hours after it was installed the battery was dead. The battery is about five to six weeks old an the auto store ran a diag. test on the battery (charge / start system) and found no problems. Can a new radio not properly installed drain the battery? Who should I take the car to for inspection? (Battery dealer or the electronic store)

2007-03-25 05:26:50 · 8 answers · asked by Anonymous

her, stuff them into the hole and run one to each terminal, or do I put one speaker wire into the hole and y-connect into two to run to the terminals?

2007-03-25 05:25:55 · 3 answers · asked by Clayton C 1

If the amp says it is 600 watts x 1 mono amp and it has 2 speaker inputs does that mean if I hook up to one input it will give 600 watts and if i hook up one speaker to each input they will each pull 300??

2007-03-25 05:16:26 · 3 answers · asked by Life Is Illusive 3

I just bought a Audiobahn Flame Q 12'' subwoffer (2200 watts max; 1100 watts RMS) for my car and my amp that I have in my car right now is much to weak, im looking to buy another amp and I was wondering if I need a 2200 watt amp or a 1100 watt amp, I have herd that if I get the 2200 watt amp that I could potentially blow the sub, but I have also herd that I could have a 5000 watt amp and could not blow the sub unless I just completely distorted it. I am just wondering if I should go with a 1100 watt amp or a 2200 watt amp with money not really being a big factor, and if you could provide some links to amps that would fit this category. -Thanks much appriciated

I am only powering 1 subwoffer.

2007-03-25 04:57:10 · 4 answers · asked by swilli4401 1

I bought four 6 1/2 inch MA Audio HK65 car speakers for my Pontiac Firbird, and I also bought four GM car speaker wire harness to connect them but there is a problem.

My factory speakers have four wires connected to them and the GM wire harness does not fit the factory harness. I was thinking about disconnecting the four wires from the factory speaker and then twist together the two positives and two negatives and then just connect it directly to the aftermarket speaker, so that the after market speakers will be connected the the factory harness and then I can just plug the factory harness back to the car.

Please Car Professionals,or people that were in the same situation as me give me some advice to see if this will work.

THANKS

2007-03-25 04:25:26 · 3 answers · asked by Anonymous

2007-03-25 03:52:11 · 6 answers · asked by miniegg 2

I just got the Rockford Fosgate P6001BD amplifier. Every where I look it says one channel, 1 x 300 @ 4 ohm and 1 x 600 @ 2 ohm. I get the amp in and there is 2 channels.... So I assumed that I should just bridge the 2 and viola, it works just fine, but I am still perplexed as to why it has 2 channels but it doesn't have any ratings for the individual channels, it only has ratings for a mono load... if you know why that is please let me know.

Thanks!

2007-03-25 03:20:22 · 3 answers · asked by Life Is Illusive 3

2007-03-25 03:01:46 · 2 answers · asked by Ed D 2

Building transferrable amplifier case from one car to another ..Case will contain 2 PDX amps ,dist.block,relays etc, need easy external connection for all speaker out leads.

2007-03-24 22:13:51 · 4 answers · asked by blackpete 1

i put the wires color to color...i have a 91 ford taurus and it has premium sound but the guy at the audio place said i can get by with a harness that is non premuim sound...i have it color to color...i have power but no sound...the blue antenna and orange wires on the harness are not hooked up cuz the orange is the dimmer and the blue there is no other place to wire it to....what may i have done wrong.

2007-03-24 18:53:30 · 6 answers · asked by gopackgo51 1

I recently just hooked my speakers up and i hear the engine i have a pioneer radio also. what can i do to solve this problem?

2007-03-24 18:06:06 · 8 answers · asked by Anonymous

I recently just put two 12s in my car and have them hooked up to a amp. I want to hook my highs up to another amp how would I hook them up? Do I need a crossover? And why do I hear the engine coming out of my speakers a little bit?

2007-03-24 17:37:28 · 3 answers · asked by Anonymous

2007-03-24 17:32:12 · 5 answers · asked by DanaDane 1

I went yesterday to BEST BUY and i bought a new radio for the car KENWOOD brand so as u know for sure the salesperson said that u can plug ur iPod into it and 100% will work.. allright then :) .. so i kept my car there for the whole day with them working on instaling the new radio to my car.. i got the car back but the iPod is not working even though i have pluged it into it .. who knows what is the deal now ,, i don't want to go back to Best buy and get sick talking to them coz am not gonna be the winner any way .

2007-03-24 17:16:58 · 1 answers · asked by arsouzy 1

2007-03-24 16:44:53 · 3 answers · asked by dave h 1

i say on trick my truck the attached rope lights to this box that made the lights flash to the beat...what is that box called and where can i find it!!!???

2007-03-24 15:46:01 · 1 answers · asked by Kyo 2

i have a AudioBahn 1206T subwoofer and and a SPL Phantom DK2-1000 watt amp. I was running 8 gauge power wire, i kept blowing inline fuses. so i stepped up to 4 gauge wire. Now i am blowing the 25A fuses on my amp. I am running a cap also. I put a 60A inline in and blew it (i normally run 80A) and 30A in the amp. The 30s blew when i put the 80A back in. So im assuming im running between 60A and 80A. I have a marine battery in my truck and when heavy bass hits it drops the volts down to like 10. so would this be a battery problem? I can run the stereo fine very low like under 20. Over that and the fuses blow on the amp so im pretty sure the amp itself is fine. Any Suggestions?

2007-03-24 15:43:47 · 3 answers · asked by BarronOhBeefDipp 1

I wired the whole system and I connected the wires from the amp to the sub but no power is getting to the sub but I'm getting power to the amp

2007-03-24 15:30:30 · 4 answers · asked by tutty850 1

2007-03-24 15:19:01 · 6 answers · asked by RONALD M 1

if so what frequency and why?...thanks plank

2007-03-24 14:30:21 · 11 answers · asked by plank h 1