Engineering - November 2006

2006-11-13 04:49:42 · 11 answers · asked by Anonymous

Steel portal frames consist of rafters and columns. What is the design principle? For what do we design these different members? Is it for tension? For shear? For uplift? Or anything else?

2006-11-13 04:40:50 · 4 answers · asked by Mokshu_zzz 1

2006-11-13 04:29:38 · 6 answers · asked by Anonymous

2006-11-13 04:14:21 · 8 answers · asked by HVAC_CPRAO 1

2006-11-13 03:56:43 · 7 answers · asked by sher a 1

I have a single data variable that varies with time. It is actually a pressure trace for a cylinder and increases to a peak over time then decreases. I want to find the the maximum pressure rise rate or maximum gradient of the curve. The curve has no equation and is just a set of time varying data points.

Is there a method for estimating the maximum gradient from the data?

2006-11-13 03:48:51 · 1 answers · asked by j_leemail 2

2006-11-13 03:38:39 · 8 answers · asked by in2buck 2

2006-11-13 03:26:48 · 16 answers · asked by Just-a-fan 3

An automobile fuel tank is filled to the brim with 45 L of gasoline (12 gal) at 20°C. Immediately afterward, the vehicle is parked in the sunlight, where the temperature is 45°C. How much gasoline overflows from the tank as a result of the expansion? (Neglect the expansion of the tank.)

2006-11-13 02:51:48 · 1 answers · asked by Anonymous

I would like to know if there are any loudspeaker model which uses rare-earth magnets. I need the models and the developers. Thanks.

2006-11-13 02:45:10 · 1 answers · asked by . 3

Failure modes and effects analysis (FMEA)

2006-11-13 01:51:09 · 3 answers · asked by Timdel 2

Some simple questions regarding engineering like whats yielding, strength to weight ratio and plastic deformation?
What is point load and distributed load?

2006-11-13 01:15:43 · 1 answers · asked by Anonymous

2006-11-13 00:49:31 · 5 answers · asked by ? 5

it is used for measurement of inductance.

2006-11-13 00:32:38 · 2 answers · asked by Anonymous

2006-11-13 00:10:28 · 4 answers · asked by marzmargs12 6

2006-11-12 21:53:07 · 0 answers · asked by Anonymous

Some simple questions regarding engineering like whats yielding, strength to weight ratio and plastic deformation?
What is point load and distributed load?

2006-11-12 21:39:58 · 2 answers · asked by Anonymous

2006-11-12 19:06:41 · 3 answers · asked by Anonymous

2006-11-12 18:57:31 · 1 answers · asked by puppy 1

a concrete mix requires 3 parts sand and 5parts cementhow many pounds of cement are neede for 75 pounds of sand?

2006-11-12 18:27:40 · 4 answers · asked by ls1boi 1

By chair, I mean the standard arm-chair.

2006-11-12 18:03:49 · 12 answers · asked by thipsuda4 1

2006-11-12 17:46:18 · 3 answers · asked by Steven A 1

Can everyone please give me any infomation about nanotechnology and any examples of nanotechnology. No restrcition for any kind of infomation given. thank you

2006-11-12 17:15:57 · 4 answers · asked by ;cherish v_ 2

Given a sinusoidal AC signal, I want to be able to clip the amplitude. :)

2006-11-12 16:30:34 · 2 answers · asked by frostwizrd 2

Please attach proper back-ups for the answer as i have to prove it. also tell me some useful links for such related discussions.

2006-11-12 15:56:02 · 1 answers · asked by just a kid 1

Any commonly used, inexpensive materials fit this description?

2006-11-12 15:55:04 · 4 answers · asked by C1N2G8 1

energy is 107.6kJ. Answer in units of kJ

2006-11-12 15:14:09 · 1 answers · asked by ruby 2

2006-11-12 14:51:47 · 5 answers · asked by lfa 1

2006-11-12 14:29:55 · 5 answers · asked by Kinloch K 1

2006-11-12 14:28:56 · 12 answers · asked by Kinloch K 1