Chevrolet

can any one tell me if GM or chevy has a web page something like this one were you can ask or get feed back on the new cars trucks have a good one

2006-12-31 23:38:34 · 3 answers · asked by runninglate 2

2006-12-31 20:06:27 · 5 answers · asked by Anonymous

I have a 2000 chevy blazer and is is running a little warm I have had the raditor clutch relpaced in July and now they have repaced the middle gasket. what does the middle gasket have to do with the car running warm

2006-12-31 19:37:48 · 5 answers · asked by jrowcarz 1

The car hesitates to start.Then it goes to1200 RPM and slowlycomes back to 1000 RPM.Occasionally on start up it has back fired.Could it be a bad fuel regulator?It has no engine codes.I`m stumped.

2006-12-31 18:40:57 · 3 answers · asked by (A) 7

75 chevy, 3/4 ton, full floaters (idk if that makes any diff) with big tires, 4 ply sidewalls,4 ply tops, 350 engine, 350 turbo, quadrajet carb tht is goin bad. I have the brake held and am on the gas all it does its just sends the tach up. a buddy of mine told me if its got a 350 it shuld def be able to.

2006-12-31 12:53:39 · 15 answers · asked by wheels47012 3

I need to carry something rather big in my four-door 1995 Blazer, but I can't figure out how to fold the back seat down. If anyone could help with this it would be greatly appreciated.

2006-12-31 12:03:52 · 4 answers · asked by Anonymous

2006-12-31 11:51:36 · 14 answers · asked by hardcore 2

I am into all monte carlos and I want to know whats the best one to get this would be my very first car. Should I get a classic or get a newer model help me PLEASE!!!!!

2006-12-31 11:26:50 · 8 answers · asked by Li-Li 2

It is an old 1942 Chevy Pumper Engine, my station wants to restore it and use it for parades. If anybody has tips on where i can look for more info and specifications i would appreciate it

2006-12-31 11:04:41 · 5 answers · asked by rebelarmyaccomplice 2

2006-12-31 10:56:08 · 5 answers · asked by cindihorkey 1

I have a GM truck rear end with 4.56 gears and a Detroit locker posi. I also have another rear end with 3.73 gears and a Gov-lock limited slip. Both rear ends are GM 10.5 ring gear and full floating axles. What I would like to know is will the Detroit locker fit inside the Gov-lock housing or do I need another housing to make it work with the 3.73 gears. Both rears come from a 1985 K30. I hope someone could tell me before I have to tear both down just to find out! Thanks! Happy New Year!

2006-12-31 08:48:15 · 3 answers · asked by krash 3

I recently bought a tach for my truck. (78 Chevy Truck), the backlight on the tach, I want it wired in to where when the truck lights are on the tach light is on, so can I run the hot wire for the light to snap behind on the the instrument cluster lights?

2006-12-31 06:17:29 · 3 answers · asked by Billy Bob 1

Heater motor is good .Can`t get it to run.What do i look for?

2006-12-31 04:13:18 · 3 answers · asked by (A) 7

I have a 1991 Caprice with a 5.0 my Question is this, If I remove my E.G.R. from the engine can it be cleaned up by me? I think it might me stuck in the open position Thanks!!!

2006-12-31 02:12:34 · 6 answers · asked by Lots of money but no sense 2

now i have no headlights, the heater works on the 3 lower settings but not high, no parking lights, the radio is dead, but the brake lights work. and all the fuses in the truck under the dash are good, is there a fuseable link under the hood some where? The local shop wants $95 just to start looking!! thanks for any help you can give....

2006-12-30 23:30:03 · 9 answers · asked by thrillmaster74 1

2006-12-30 23:12:05 · 3 answers · asked by aikon56 2

Asking all the Cavalier owners out there; what has gone wrong with their cavaliers(as in repairs) throughout the car's lifetime?
Mine is(im at 140,000km):
Radiator
water pump
serpentine belt and tensioner
front wheel bearings
and oil changes and general maintenance

2006-12-30 20:56:16 · 5 answers · asked by Anonymous

2006-12-30 15:31:16 · 11 answers · asked by Chaley2525 1

and the GM 3800 engine? like gas mileages,power,etc. The reason is I am test driving a 2003 chevrolet monte carlo and it has a 3400 SFI engine in it. I have owned a 1989 pontiac bonneville in the past that had a 3800 and I know that car got great gas mileage. I would appreciate hearing from a certified mechanic that is familar with the two engines or anyone that is famillar with the two engines.

2006-12-30 15:00:45 · 6 answers · asked by Papa WILL 6

i have done everything to my intake on my truck a granatelli mass air flow k/n cold air filter and a 80 mm thotle body and i all so have short type headers and hytech programmer runs great but engine light is on and the code is showing lean air mixters on both engine banks is there a way to fix this or is ok to run it this way?

2006-12-30 14:37:23 · 3 answers · asked by John F F 1

I have a 2001 chevy silverado 1500 HD with coil near plug. Do they make msd ignitions for this type of system. If so do I have to buy 8 seperate coils or is there another way to replace your ignition system with MSD. What is the average cost of the type of system I am looking for.

2006-12-30 13:44:14 · 3 answers · asked by Anonymous

My windsheild wash fluid is not coming out...I have taken an air can and blew the air through the hose where it is connected on the wiper blade and the the washer fluid bubbled in the reserve tank. So I know the hose is not clogged, I am now wondering if there is a fuse that I can check that may be out and is causing the washer fluid not to come out?

2006-12-30 12:15:01 · 6 answers · asked by Ange 1

the loud pop comes when i make a sharp right to fast or brake to hard but it dose not hapen untill i start to go again srom the hard stop but it happens at the time of the hard right turn but olny when i am going fast and i don't meen brake neck fast just kinda like getting on it to merge if that makes sence

2006-12-30 11:08:35 · 7 answers · asked by lala4988 1

from a "drivers side dipstick" year era intake manifold fit on a "passenger side" dipstick era small block chev. I'm researching whether or not what goodies i already have will work on the downstroked 377, im building for my 64 Chevy II p.s. "I'll send you a pic if you ask, incase you love these cars like i do!"

2006-12-30 10:03:18 · 8 answers · asked by notchydaddy1 2

My truck tries to start ,but will not run. It sounds like a fuel filter except it was running up until we shut it off

2006-12-30 09:50:27 · 6 answers · asked by Chris W 1

I own a 1991 Caprice with a 5.0 engine. I need to know if a loose connection on a knock sensor could cause a ignition misfire when the car is in closed loop operation. the car runs great when cold but after it warms up to full opp. temp. and I put a load on the engine I get a ignition misfire all 8 cylinders cut in and out. so if you could please let me know what the symptoms of a loose connector on a knock sensor would be. Thanks!

2006-12-30 07:10:56 · 10 answers · asked by Lots of money but no sense 2

Trying to get 2 new remotes prorammed into an '02 Blazer that I just bought. I know that there is a system for doing this.

2006-12-30 06:25:29 · 3 answers · asked by Kevin S 1

2006-12-30 02:59:04 · 8 answers · asked by wmonte05 1

I hope someone can shed some light on a few questions.I had a 283 bottom end machined for rebuilding and the machine shop also rebuilt a set of 350 ( Cast no-3947041 / 64 cc Heads ) for me .I built the engine with new pistons rings and bearings.The engine then sat for about 5 years before firing as the hot rods taken a few years to build.Does anyone know the correct plugs for these heads as Ive been running the engine with NGK-BP5FS plugs ( The car is not licenced yet so the engine has only had the cam run in an then fired and run for a while on several occations when moving it)
The plugs are running a bit rich but every time I've removed the plugs there's been oil around the threads of the plug and a bit above.I've done a compression test and all cylinders have been between 153 psi & 158 psi I could be wrong but I'm wondering if the Guides were not reconditioned when rebuilt and oil is being let into the bores.Can anyone please shed some light on the problem.

Nick

2006-12-30 00:39:07 · 9 answers · asked by fitzy 1

I own a 1991 Caprice with a 5.0 engine and I need to know the exact location of the knock sensor. Is it on the block? and if so where??? I need to check the conector to see if its clean and conected to the system Thanks!!!!

2006-12-29 23:14:10 · 4 answers · asked by Lots of money but no sense 2