English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

9 answers

Blurryness Is usually caused by slow shutter speeds. Basically when you click on the button your camera can not gather enough light on the sensor so it leaves its shutter open too long resulting in a blurred image.

The best way to not get a blurry image is to turn up the iso...iso is a setting that represents how sensitive your film or sensor is.
Or if you have some control over your shutter then don't let it drop below about 1/30th of a second for hand holding it. If you dont have a SLR chances are you can't do this.
Another option is to use a flash which will force your camera , if it is one where you don't have any control, to use a faster shutter speed.

2007-12-03 20:16:24 · answer #1 · answered by MrVx 2 · 1 0

I'm sorry if this is insulting, but I have no knowledge of your prior experience. Often the cause of blurry pictures is moving your hand too soon. You may be used to taking pictures with a non-digital camera. There is considerable shutter lag with point and shoot digitals and you have to be sure to hold still for long enough for the camera to actually take the picture. This will take up to a full second. Watch the little green light (usually) on the back of your camera. Hold the button half-way down and wait until it lights up steady instead of blinking. This means the auto-focus operation is complete. Press the button the rest of the way down and hold it there for about a second to allow time for the shutter to actually take the picture. Good luck!

Here's a link showing a chart of various cameras and their shutter lag:
http://www.cameras.co.uk/html/shutter-lag-comparisons.cfm

2007-12-03 23:01:05 · answer #2 · answered by Picture Taker 7 · 1 0

My guess (and that's all it is without knowing more of what you're doing) is #1 you need to increase the ISO (see your manual) #2 you need yo use the flash indoors #3 you are probably hold the camera out looking at the LCD and that doesn't stabilize the camera very well. Try the eyepiece or a tripod.

2007-12-04 00:15:28 · answer #3 · answered by Perki88 7 · 0 0

i have a different suggestion than the other answerers. are you using the flash? answerer number one had a great suggestion and he explained it correctly. If I were you I'd make sure to always use the flash and make sure the ISO speed is set to Auto.
some cameras have a selecter button that chooses pre-installed settings like sports, outside, inside.... set yours to cmera mode or auto. or just mess with that a little.

2007-12-03 20:49:52 · answer #4 · answered by BIG 4 · 1 0

When all else fails, READ & STUDY the Owner's Manual for your camera. Learn how to use your camera and your pictures will turn out better.

2007-12-03 21:34:26 · answer #5 · answered by EDWIN 7 · 2 0

Are you using the fully-automatic option?
My next-door neighbour just didn't bother to read his manual and was framing up his shot and then hitting the button. He had not allowed the camera to focus.

2007-12-03 22:49:58 · answer #6 · answered by Anonymous · 1 1

Because your shutter speed is slower than 1/250 sec.

2007-12-04 16:03:45 · answer #7 · answered by V2K1 6 · 0 0

Because wrong setting of your Aperture,it must be set at f/8 or f/11,so that it will give your pictures sharper images.

2007-12-03 20:39:06 · answer #8 · answered by victor98_2001 4 · 1 0

operator error,

use a flash or higher iso, or bigger/smaller apeture, read your manual and see what it says, use a tripod,

z

2007-12-03 21:29:39 · answer #9 · answered by Antoni 7 · 2 0

fedest.com, questions and answers