2007-09-28 03:32:33 · 11 answers · asked by Anonymous in Computers & Internet ➔ Hardware ➔ Add-ons
pc 2700 auto downgrades to 2200 if it needs to
but others do not
also make sure both stick or how many ever sticks of ram are firmly socketed 1 bad connection will make it not work and your computer will then make a beeping noise.
also did you make sure you ground yourself before touching the ram? static electricity will demolish a computer
if your comp doesn't start up at all i suspect static discharge frying something
if it beeps the ram isn't socketed properly or is the wrong type
2007-09-28 03:58:06 · answer #1 · answered by Thumbs Down 3 · 0⤊ 0⤋
Did you use precaution when installing the RAM, such as either touching the side of the computer before putting your fingers on the parts or using an ESD strap? Are you sure the new RAM matches the specs of the old RAM? Is there an error message that describes the problem, or do you get any POST error beeps? Does the computer turn on at all?
2007-09-28 03:36:53 · answer #2 · answered by Thomas K 4 · 0⤊ 0⤋
Awesome question and thank you for participating in Yahoo's Q & A. A lot of people have experienced the same problem when adding memory to the machine. First of all, every machine maxes out on the amount of memory that can be added. Some cannot exceed 1 gig, others at 2 gigs etc. By exceeding it's abilities, you cause it not to work at all. Also, you need to make sure that your using the same type of ram memory as the existing memory that's already installed. Some can't be mixed. It will be marked PC2700 DDR, PC3200 DDR etc. etc. Any computer store can make sure that you get the matching type for your machine specifically. Thanks again for the question. Larry (RadioShack 01-9590)
2007-09-28 03:44:30 · answer #3 · answered by dumbbutt4321 4 · 1⤊ 0⤋
Take out the new memory module and see if your PC works.
If not then you've most likely knocked some connection, check all the wiring and the connections, then try again.
If it does then re-try the memory module again, remembering not to touch the module with your greasy finger tips, use a bit of paper or something between your fingers and the module.
If your PC fails to work with the new module in then you've gone and bought the wrong type or you've bent/broken the points by forcing the module in.
If you're not sure then take the PC to a specialist and be prepared to fork out a small fortune.
2007-09-28 08:46:52 · answer #4 · answered by blissman 5 · 0⤊ 0⤋
Without knowing more about your problem. I would suspect corrupt ram chips. Does your computer work fine after you remove the newly added Ram ??
2007-09-28 03:37:06 · answer #5 · answered by Anonymous · 0⤊ 0⤋
here could be some possible causes
1. Two different kinds of RAM installed
2. RAM not inserted properly
3. A wire left unplugged or out of place
i would try re-seeding the ram, or taking it out and putting it into a different slot
2007-09-28 03:38:32 · answer #6 · answered by Anonymous · 0⤊ 0⤋
Your board might not be compatible for the ram you have purchased. Get it checked by a qualified engineer.
2007-09-29 11:43:53 · answer #7 · answered by Anonymous · 0⤊ 0⤋
Either the RAM is installed incorrectly or is not compatible.
2007-09-28 03:36:54 · answer #8 · answered by Yoi_55 7 · 1⤊ 0⤋
You probably haven't fitted it properly. Take it out again and try reinserting it, it might not have "seated" properly.
2007-09-28 03:43:19 · answer #9 · answered by Sparky 6 · 0⤊ 0⤋
how much ram did you start with...and is it the right ram..too much ram will kill your pewter
2007-09-29 01:21:58 · answer #10 · answered by Anonymous · 0⤊ 0⤋