English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

I am looking to paint some broad "striping" on an interior wall of a retail showroom. I know the basics (masking, etc.) but I would like to know if there is a more efficiant way to accomplish this task... Or maybe you D.I.Y. painters out there have some industry secrets you can let me in on.

I look forward to your responses!

2007-09-12 07:43:57 · 6 answers · asked by AG 33 & A Third 3 in Home & Garden Decorating & Remodeling

6 answers

Paint the walls the base color, this is the larger portion of stripes color, the one that covers the biggest area, its also the lighter color. After it dries, measure your walls, decide the size of the stripes, in each color, mark off the stripes with a pencil, then snap a chalk line for the stripes all the way around the room, you want it symmetrical. Use painters blue tape to tape on the chalk line, its the best to use because you can leave it up for like two weeks and still be able to peel it off without chipping and peeling everything. Then go through and use a small piece of tape to mark off the sections that do not get painted, trust me on this one, because you don't want to have to go back and re-do a stripe. Then after the tape is securely in place, edge all the stripes with a paint brush/sponge or mini roller, and by the time you're back to the beginning stripe it'll be dry enough to roll on the second color. Do all the stripes and when done start at the beginning stripe again and slowly peel away the tape. Make sure the tape doesn't get on the walls, because it could still have some wet paint on it and tarp the floor for the same reason. Have a trash can with a bag in it ready for the tape. Good luck.

PS it goes faster with the help of a friend/spouse.

2007-09-19 03:35:59 · answer #1 · answered by Anonymous · 1 0

With a LOT of painters tape, a lot of patience, a lot of snapped level lines.... if your lucky depending on your colors you can base paint the wall with the lightest color then all your doing is painting the stripe... if your colors will bleed through or change then you have twice the work and twice the time as everything has to be done twice!
It will look great when your done and you will a lot of pride in your showroom! Take your time... do it right, there is no really easy way!

2007-09-20 05:10:35 · answer #2 · answered by Anonymous · 0 0

A fun project with big payoff when done. You will need to mark your lines first than tape them off with painters tape and paint the first color. When dry remove the tape and apply new tape now onto the paint evenly with the paint or exposing just a tiny bit of the new paint. Than apply the second color, let dry, remove the paint and ENJOY
It is a great look, my wife did it in our bedroom, fantastic results.
Good Luck!

2007-09-17 13:24:29 · answer #3 · answered by Derek 4 · 0 0

whilst human beings point out blue painters tape they advise low adhesion style tapes. this might help end your protecting tape from removing your extra energizing paint, from previous adventure I incredibly have discovered that portray the wall with between the colors first works the final. enable a minimum of 24hrs to your paint to dry, a pair of days in case you are able to. degree your wall and Davide it up into the sections to your stripes and mark with a grey lead, use the tape on the outer of your stripes as a handbook. i found that in case you will get reliable insurance with one coat and peel your tape remote from the paint after drying, you wont get a buildup of paint on the perimeters. hint! determine you wipe over your tape firmly so the paint does not seep under the perimeters. probably extra perfect to apply a broom for the stripes as a curler will lay the paint on very thick, determine you lay the paint off with your brush as we communicate up and down. wish this helps Marty Down under

2016-10-10 11:00:33 · answer #4 · answered by ? 4 · 0 0

I'm no expert on this but I know that you need to snap it first with a chalk line before you tape. I don't know of any other way to get good striping.

2007-09-12 09:01:09 · answer #5 · answered by dawnb 7 · 0 1

first make sure your tape is on tight
before using your roller, use a paintbrush and put a thin
coat along the edges of the tape then let dry a bit before
rolling....this keeps it from bleeding under the tape.

2007-09-12 08:04:08 · answer #6 · answered by silverheelsX 2 · 1 0

fedest.com, questions and answers