2007-09-06 10:25:00 · 6 answers · asked by joycewrecker2 1 in Cars & Transportation ➔ Car Makes ➔ Ford
The following directions are copied from pages 116-117 of your owners manual:
*******COPY***********
Deactivating/activating the BeltMinderfeature
Read steps 1 - 9 thoroughly before proceeding with the
deactivation/activation programming procedure.
The BeltMinderfeature can be deactivated/activated by performing the
following procedure:
Before following the procedure, make sure that:
² the parking brake is set
² the gearshift is in P (Park) (automatic transmission) or the neutral
position (manual transmission).
² the ignition switch is in the OFF position
² all vehicle doors are closed
² the driver’s safety belt is unbuckled
² the parklamps/headlamps are in OFF position (If vehicle is equipped
with Autolamps, this will not affect the procedure.)
To reduce the risk of injury, do not deactivate/activate the Belt
Minder feature while driving the vehicle.
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT
START THE ENGINE)
2. Wait until the safety belt warning light turns off. (Approximately 1–2
minutes)
² Steps 3–5 must be completed within 60 seconds or the procedure will
have to be repeated.
3. Uncoil then retract the safety belt three times, ending with the safety
belt retracted. This can be done before or during BeltMinderwarning
activation.
Seating and safety restraints
116
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Uncoil then retract the safety belt three times, ending with the safety
belt retracted.
² After step 5 the safety belt warning light will be turned on for three
seconds.
6. Within seven seconds of the safety belt warning light turning off,
uncoil then retract the safety belt.
² This will disable BeltMinderif it is currently enabled, or enable
BeltMinder if it is currently disabled.
7. Confirmation of disabling BeltMinderis provided by flashing the safety
belt warning light four times per second for three seconds.
8. Confirmation of enabling BeltMinderis provided by flashing the safety
belt warning light four times per second for three seconds, followed by
three seconds with the safety belt warning light off, then followed by
flashing the safety belt warning light four times per second for three
seconds again.
9. After receiving confirmation, the deactivation/activation procedure is
complete.
*******END COPY*************
I HIGHLY recommend that you download the entire manual and read the manufacture warnings about seat belts. The chapter begins on page 113.
I have provided the link to the free down-loadable manual in the "source" box below.
It is in pdf format & is eaily saved to your computer for future reference.
2007-09-06 16:43:45 · answer #1 · answered by Vicky 7 · 2⤊ 0⤋
The seatbelt chime is part of the instrument panel. To disconnect it you'd be talking about modifying an electronic circuit board. Are you up for that?
If you're asking about the chime because you don't wear your belt, well, that's another issue.
2007-09-06 10:54:27 · answer #2 · answered by VO 3 · 0⤊ 1⤋
there's a small field plugged into the returned of the fuse panel or on the component of it. if u pay attention for the buzzer and experience the relays u will discover the single that creates the sound. eliminate it and u don't have from now on issues. of direction the terrific thank you to end it could be to positioned on your seat belt.
2016-10-10 02:13:17 · answer #3 · answered by ? 4 · 0⤊ 0⤋
under the seat disconet the clip thet has the cables
2007-09-06 13:46:26 · answer #4 · answered by Anonymous · 0⤊ 0⤋
Put your seat belt on.
2007-09-06 12:14:42 · answer #5 · answered by (A) 7 · 1⤊ 0⤋
find the speaker and clip the wires behind it!
2007-09-06 10:30:03 · answer #6 · answered by Anonymous · 0⤊ 0⤋