Not getting to Network 2 PC's to share files.?

Question

I'm using windows XP on both comps,I have them connected with the cable between the 2 network cards but when i run network setup wizzard its says wizzard found disconnected hardware on both systems,i have both cards perfectly inserted into the computer,remember i just wanna share and transfer files between these pc's,please help me

Answer 1

You say the NIC (network interface cards) are properly inserted. I further presume their drivers were installed; if not be sure to do so.

Do you have a CROSS cat 5 cable; a straight will not work in this case because you are not using a network switch. A cross cable has Pin 1 on left cable end connect to Pin 3 on right cable end; Pin 2 to Pin 6, Pin 3 to Pin 1, pin 6 to pin 2.

Did you assign static IP addresses to both pcs? YOu do not have a dhcp server so you need static; I would make pc1 ip 192.168.1.11, subnet 255.255.255.0 default gateway 192.168.1.11 and for pc2 ip 192.168.1.12, subnet 255.255.255.0 default gateway 192.168.1.11 and not worry about DNS servers. To set static IP open network connections, right click on the LAN connection, select properties, select Internet Protocol (TCP /IP ) from the center, click on properties and fill in blanks.

Make sure you can ping the other pc. Open command prompt (start - run, type in cmd and hit enter); and from pc 1 type "ping 192.168.1.12" without the quotes and hit enter; this assumes you used the LAN IP that I suggested above; you should receive 4 positive responses; go to PC 1, and ping using "ping 192.168.1.11". If you can ping you have connection.

Now you must network share the files and make sure you have access permissions for both pcs; if you need help w. that write again

Answer 2

First of all you need to install drivers for the network cards. If you have done this goto the next step
Open control panel and then open network connections
From the connections listed in the Lan group and internet gateway group right click on all the connections and select
enable.

right click on the connection for the lan card connection through which you want to create a network, select properties
From the general tab, put a checkmark against Internet Protocol(TCP/IP) and select it. Click properties

A Internet Protocol (TCP/IP) dialog box will appear
Select Use the following address
Give the following given values
IP Address : 192.168.1.2
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
Click on Ok

Do this for every computer on the network except for the IP Address
For the next Computer increment the 4th value of the IP address for each computer like 192.168.1.3 , 192.168.1.4, and so on

Answer 3

before everything there is allways a manner, yet to respond to good, you ought to be extra specific.... In a customer server environment( which you do not have) there is the skill to replica folder suggestions between desktops, so as that the information are obtainable on distinctive computing device's and that they do no longer seem to be placed in one specific folder. on your case, It relies upon on what precisely you're attempting to end. no count number if that's database suggestions including outlook or get admission to, there are alot of application courses which could assist you synchronize your infromation from one computing device to a distinctive (kinda like the hotsync supervisor for palm pilots) in case you desire to have a replica of your computing device records backed up on the computing device, then its probable suitable to look into ghost or another application to photograph the force. whilst you're basically backing up specific folders and information, the backup application in domicile windows does a important interest. in spite of everything, possibly giving somewhat extra factor will help somebody else get you an answer! desire this helps!

Answer 4

You need a CAT5 CROSSOVER (not regular) Ethernet cable. Connect the two ports with that, and it should work. Otherwise, you need a hub or a router if you want to connect with regular cables or add anohter machine, you will have to have a hub or router.