2007-03-14 18:07:52 · 7 answers · asked by Anonymous in Cars & Transportation ➔ Car Makes ➔ Ford
F SERIES 1994 -1996
12 VOLT CONSTANT YELLOW (+) IGNITION SWITCH HARNESS
STARTER RED/LIGHT BLUE (+) IGNITION SWITCH HARNESS
IGNITION 1 RED/LIGHT GREEN (+) IGNITION SWITCH HARNESS
IGNITION 2 BLACK/LIGHT GREEN (+) IGNITION SWITCH HARNESS
IGNITION 3 N/A
ACCESSORY/HEATER BLOWER 1 GRAY/YELLOW (+) IGNITION SWITCH HARNESS
PARKING LIGHTS ( + ) BROWN (+) @ HEADLIGHT SWITCH or in DRIVERS KICK PANEL
POWER LOCK PINK/YELLOW (TYPE C) See NOTE *1 IN EITHER KICK PANEL
POWER UNLOCK PINK/LIGHT GREEN (TYPE C) See NOTE *1 IN EITHER KICK PANEL
DOOR TRIGGER BLACK/LIGHT BLUE (+) IN DRIVERS KICK PANEL HORN DARK BLUE (-) @ STEERING COLUMN HARNESS
TACH TAN/YELLOW @ IGNITON COIL
BRAKE LIGHT GREEN (+) @ SWITCH ABOVE BRAKE PEDAL
FACTORY ALARM DISARM DARK GREEN/PURPLE (-) IN DRIVERS DOOR HARNESS
NOTE *1 If equipped with FACTORY KEYLESS ENTRY, Vehicle is a TYPE "B" Door Locking System, WITHOUT FACTORY KEYLESS, This is a TYPE C Door Locking System and you MUST get the lock and unlock wires in the PASSENGER KICK PANEL (Parking Brake Braket is in the way) you MUST also TEST for SWITCH and MOTOR wires ONLY with the DRIVERS DOOR SWITCH. On this TYPE C System you MUST TEST from the DRIVERS DOOR Switch only when testing for SWITCH and MOTOR wires.
Keep in mind you are going to need a Transponder By Pass module in order to by pass your ignition switch. You will also need a spare key as you need one inside theby pass kit to fool your ohms resitance in your key switch.
It is a very simple hook up you will need to remove the steering wheel shroud, & remove ignition.The easy way to remove ignition is press the silver button on the underside with key in run position, with button pressed a simple tug should do ya.
Then you want to wrap antenna wire on the plastic housing as close to key switch as possible, then secure with a good zip tie.This can be a trial & error process, You simply have to find the sweet spot, so to say.
Transponder is a simple 3 wire hook up .Power , ground & factory alarm shutdown wire.If vehicle will not start put key in ignition & if it starts then you know it is a transponder by pass problem.DO NOT CUT TRANSPONDER ANTENNA....
keep in mind depending on the unit you install, you may need relays for your door locks to function properly.
2007-03-14 19:37:32 · answer #1 · answered by Skull 5 · 0⤊ 0⤋
Remote Start Wiring Diagrams
2016-11-16 17:07:15 · answer #2 · answered by Anonymous · 0⤊ 0⤋
Buy a Haynes manual from your local auto parts store, it'll have a complete wiring diagram for your vehicle.
2007-03-14 23:15:33 · answer #3 · answered by ? 5 · 0⤊ 0⤋
Go to www.the12volt.com and sign up as a member on their forums (its free) and they have tons of vehicle wiring diagrams, they might just have what you need,
2007-03-14 18:22:32 · answer #4 · answered by maybayus123 3 · 0⤊ 0⤋
the company that made the remote start has a web page with detailed instructions per vehicle to install..(do a google search) thank you
2007-03-14 19:10:25 · answer #5 · answered by doug h 5 · 0⤊ 0⤋
auto zone has a web site with wiring diagrams.
2007-03-14 21:33:39 · answer #6 · answered by Fordman 7 · 0⤊ 0⤋
Most parts guys at the dealerships will give you a photo coppy from their computor. They have for me.
2007-03-14 18:43:54 · answer #7 · answered by Anonymous · 0⤊ 0⤋