2001 dodge 2500
2007-01-16 01:21:46 · 10 answers · asked by Anonymous in Cars & Transportation ➔ Car Makes ➔ Dodge
Sounds like you have a short in the wireing there could be a small spot where it has worn through take it to a dealer or jack it up and see if you can find a bad spot but most of the time you can not just follow the wire they are hidden in the undercarriage of the car have the mechanic look at it.
2007-01-16 01:32:01 · answer #1 · answered by Mary B 5 · 0⤊ 0⤋
The wiring from the brake light switch is routed up the steering, thru the turn signal switch and back down the steering column then back to the lights. There is a plug at the lower end of the steering column which the wires run thru. Check to see if the plug is made or if any wires have been pulled out. If Both brake and turn signal lights are not working and fuses are good then there is most likely a problem somewhere in that wiring or possibly in the turn signal switch.
2007-01-16 13:21:15 · answer #2 · answered by mustanger 5 · 0⤊ 0⤋
The brake problem-free circuit runs by ability of the turn signal swap so that you've a project there yet you want to locate the fuses first. On some Chrysler automobiles the fuse panel is interior the glove field.
2016-10-15 07:26:04 · answer #3 · answered by Anonymous · 0⤊ 0⤋
some vehicles run the blinkers through the hazard switch, check to see if that works, you need to get a test light and see if the tops of the fuses are live, there are usually another main set of fuses in the engine compartement,
2007-01-16 01:34:30 · answer #4 · answered by rich2481 7 · 0⤊ 0⤋
do the turn signals light up but not flash and the tail lights not work? if those are the problems, it could be your flasher. I thought dodge's had the combination flasher, my 98 dakota had the problem above and i had to get a combination flasher from a dodge dealership. Can't go to autozone to get them. If i can recall correctly it was like $40 for the part, but don't quote me on that, it was a couple of years ago.
2007-01-17 02:58:48 · answer #5 · answered by The Mullet 4 · 0⤊ 0⤋
FreddyBoy is on the right track, Many cars purposely disable the blinkers to let you know your brake lights are out.
2007-01-16 02:07:36 · answer #6 · answered by daffyduct2006 6 · 0⤊ 0⤋
I doubt all your bulbs are blown...so, do you have a towing package? if so make sure that the quick connect for the trailer is hooked together, if so then I would start by checking for voltage at the socket, if you have voltage there to a known good ground, start checking your ground wires.
2007-01-16 01:31:59 · answer #7 · answered by kerfitz 6 · 0⤊ 0⤋
One bad bulb can screw up all your blinkers. I would check each bulb (remove each one, hold it up in good light and examine the
filiment(s)...) before doing anything else.
2007-01-16 01:31:04 · answer #8 · answered by FreddyBoy1 6 · 0⤊ 0⤋
Could be a short in the system somewhere.
2007-01-16 01:29:10 · answer #9 · answered by dead_end_lies 3 · 0⤊ 0⤋
could be the bulbs are broken or wires are crossed or severed somewhere
2007-01-16 01:29:48 · answer #10 · answered by topgunpilot22 4 · 0⤊ 0⤋