I think I saw it on some DIY show- the plywood was cut into piesces, stained and coated with polyurethane. At least I think it was plywood. It was so unique looking! Has anyone ever0 tried this and are there different types of plywood or anything else I should know? Thanks!
2007-01-07 07:17:23 · 17 answers · asked by mattysmom 1 in Home & Garden ➔ Decorating & Remodeling
where can I purchase finish grade plywood?
2007-01-07 07:22:47 · update #1
Yes, I've used plywood on flooring in a store we decorated. This went down over a concrete slab, so there was adequate support from underneath and it could be glued down without the use of nails. (We used 3/4 inch.) If you are going over framing, make certain you use thick enough plywood to prevent warpage. Also, plywood comes in different grades. Use one that has a "finished" good side for the best results. Look for the sides that have no splits or knot holes for the best results. We also sanded before we stained and sealed for a smoother finish and to keep the grain looking good. We laid it so that the grains were in a square pattern meeting in the middle of four pieces of plywood, but it also looked nice having the grain all going the same way. It took about 5 coats of non-yellowing polyurethane to get a durable finish that has lasted now for about 9 years. One other tip, you may have to cut the edges for a tighter fit where the plywood joins another piece. We found several that left an unsightly gap and we had to trim the edges. Just purchase the best grade of plywood (Lowes carries the best finish grade plywood) you can afford and you will be happy with the results.
2007-01-07 07:20:04 · answer #1 · answered by eskie lover 7 · 1⤊ 1⤋
Finished Plywood
2016-10-05 01:40:31 · answer #2 · answered by pendergast 4 · 0⤊ 0⤋
You can get finish grade plywood at pretty much any hardware store (Home Depot has it for certain). It is NOT cheap, just so you know. You might consider a lower grade of plywood and rent an orbital sander, go over it to smooth it out before cutting it into strips. Last time I bought plywood it was $29 for a sheet of 3/4 inch thickness (it all comes in 4 ft x 8 ft sheets) and that was regular construction grade. I think the finish grade was double that. For a heavy wear or wet area, it'd be a bad idea. You'd be paying almost as much as you would to just put down a good laminate or vinyl flooring in the long run, and it won't last as long.
I put down regular plywood in the pet room, sanded it with the orbital, and painted it with a floor paint, then put a clear epoxy down on that. It turned out pretty well and if it does get trashed, it won't be a big deal to lift up a section and replace it. I'd not use the polyurethane, a water based one will not be durable and the oil based one will turn yellow on you.
2007-01-07 07:27:10 · answer #3 · answered by Jadalina 5 · 0⤊ 1⤋
You can use anything you want. There are many types and thickness's of plywood. It sounds like you already have a sub floor and are thinking of using plywood as your finished floor as well. The problem with plywood is that it is made up of thin layers of wood glued together. You can get oak, mahogany etc veneered plywood, You can also get what is called, furniture grade, or finished grade plywood. (very Expensive) If you use plywood, make sure it is at least 5/8" thick instead of finish grade buy utility grade and rent a floor sander (cheaper) make sure to use the proper glue. You must seal the joints with caulking if water gets into joints the plywood could buckle. Also watch that the grain of the wood all goes in the same direction.
2007-01-10 13:05:29 · answer #4 · answered by ? 6 · 0⤊ 1⤋
I would have the plywood cut in to planks and install them over the existing flooring. I can not use or remove the vinyl flooring. It has nails and staples on the flooring, and it has been cut away from the base trim. It is the original flooring.
I also would like to know about using an electrical brad gun. What size of braid nails would I need. I would appreciate any suggestions on this matter. Does all plywood which is being use as flooring have to be sanded? The DIY shows it not being sanded, and they suggested to purchase the plywood which has the most knots, etc. so that it will look like installation of a wood floor. Should I nail and glue the planks? What about caulking?
Thank for taking time on this matter. I await your response.
2016-08-13 03:39:35 · answer #5 · answered by Dorina 1 · 0⤊ 0⤋
I have installed plywood as flooring, I used a router to cut shallow v-shaped grooves in the plywood to replicate 8" squares. I then finished it with several coats of poly-urethane. Looks great. You will have to use a plywood with one side sanded or with a finish veneer on it. Depending on what you are laying it over will determine the thickness needed. If you existing floor is uneven, you may have to use a thicker plywood, such as 3/4". If your existing floor is fairly level, without any big dips, 1/2" ply should be ok.
2007-01-07 07:31:38 · answer #6 · answered by bryan s 2 · 1⤊ 1⤋
I am not an expert. (an expert would probably say NO!)
I guess you can, I don't see why not.
What is down now? What would you be working on top of?
(the sub-floor) - ?
If it is already smooth and level.... go for it.
Be aware that plywood is SOFT. It will gouge and dent fairly easily. You can get hardwood plywood.. it will cost more.
If you have a smooth level subfloor... Luann (pronounced Lou-on) plywood will do. It's like unfinished panelling and is often used as subfloor itself.
How will you make it stay down? (I recommend LIQUID NAILS)
Another cheap method: if you have smooth already... Paint.
Floor paint is cheap and easy and made for flooring.
2007-01-07 07:29:20 · answer #7 · answered by marcus 4 · 0⤊ 1⤋
The thing about using plywood as a flooring is that plywood shreds and splinters with daily use as feet tread on the plywood. The coat(s) of polyurethane will not keep the plywood from shredding away with use. Also, you cannot really scrub or wax or efficiently clean the floors of plywood.
TV design remodeling shows are frequently not the best as remodeling advice as far as actual daily use goes.
2007-01-07 07:26:28 · answer #8 · answered by Anonymous · 0⤊ 1⤋
For the best answers, search on this site https://shorturl.im/ayfLk
I think leveling up what's there, putting down a layer of plywood and then the Pergo is the best option. I wouldn't worry about the weight factor, adding plywood won't add much weight per square foot. Can you inspect the joists from below, basement or crawlspace? On the other hand, maybe the owner has made such a mess of things there won't be any choice but the nuclear option.
2016-04-04 21:57:01 · answer #9 · answered by Anonymous · 0⤊ 0⤋
I would not plywood is good for a sub-floor but that is it ..the longevity would be very short and it would look very worn very fast because of the fact the plywood is made from soft woods but can be purchased with a veneer but that does not fix the problem being the veneer is extremely thin good luck
2007-01-07 10:52:52 · answer #10 · answered by doubleg_81423 2 · 0⤊ 0⤋