2006-11-13 06:45:17 · 11 answers · asked by OhWoizme 2 in Food & Drink ➔ Cooking & Recipes
sure you can....use any shape you want
after it is set then just stick it in hot water for a few moments and giggle it around a bit
flip it over on a plate and there you have it.
2006-11-13 06:48:21 · answer #1 · answered by spider 3 · 0⤊ 0⤋
Plastic Jello Molds
2016-11-10 21:26:07 · answer #2 · answered by ? 4 · 0⤊ 0⤋
Yes you can do it all the time !!! just make sure that is not to deep so there is not a whole lot of space to fill so when you unmold it easier. to loosen the jello just put it for a moment in warm water or even just take a kitchen towel dump it on hot water then wipe the mold all around the out side and when you shake and the whole thing moves you're ready to unmold..
2006-11-13 06:51:01 · answer #3 · answered by wanna_help_u 5 · 0⤊ 0⤋
Yes. Spray well w/ Pam first.
To unmold, dip bowl down into a sinkful of hot water for a few seconds, then lay serving plate on top of bowl, hold the 2 together, and flip quickly. Be patient. If it remains stuck, try loosning the edge w/ a knife, or tillting sideways so one side of it comes out before the other. Once the "seal" is broken, it will come out.
2006-11-13 07:06:12 · answer #4 · answered by Sugar Pie 7 · 0⤊ 0⤋
Yep, it's a two-step process. VERY VERY lightly spray the inside of your container with "Pam" cooking spray, and pour your jello in like usual. When you're ready to unmold the jello, dip it in hot water for a few seconds to loosen it up. It should slide right out.
2006-11-13 06:53:42 · answer #5 · answered by kc_warpaint 5 · 0⤊ 0⤋
Any container can be used as a mold!
When the Jell-O is set, just place the container in warm water for a few minutes. This will lightly melt the Jell-O and make it easier to slide out.
Make sure you don't put too much water so it won't go in the mold, and dry you mold before inverting!
2006-11-13 06:51:58 · answer #6 · answered by Cruella DeVil 3 · 0⤊ 0⤋
You should do it yourself in chocolate- all you have to do is cover any openings with latex, such as a piece of latex glove then cover in petroleum jelly so it doesn't stick and cast the body part with plaster. You can get quick dry plaster at a craft store. Once the plaster dries, carefully remove it and then you can use this cast as a mold for any material you want. Wax, certain plastics or chocolate, which I highly recommend.
2016-03-17 07:08:32 · answer #7 · answered by Anonymous · 0⤊ 0⤋
Yes you sure can...you can either use a little pam spray and wipe it with a paper towel all around the bowl or use a little oil on a paper towel and wipe it in the bowl...it doesn't take much..just make sure it is all over the bowl! I hope this helps!Loretta
2006-11-13 06:52:54 · answer #8 · answered by Anonymous · 0⤊ 0⤋
You can use just about anything for a mold if you line it with plastic wrap.
2006-11-13 06:51:15 · answer #9 · answered by WeaselLuvr 2 · 0⤊ 0⤋
yes, dip the bottom of the bowl in hot water for a few seconds to unmold.
2006-11-13 06:52:34 · answer #10 · answered by practicalwizard 6 · 0⤊ 0⤋