I want to paint them and I've been told that I should use Acrylic paint.
Do/should I treat the bricks first before I paint them ?
They are particularly dirty above the sink and cooker, is there a spray cleaner suitable for this ?
2006-09-08 03:14:55 · 9 answers · asked by FRAN1 3 in Home & Garden ➔ Decorating & Remodeling
It might be an idea to seal the bricks before you paint them - to stop any remnants of grease that you couldn't clean off from showing through. There are lots of off-the shelf products which are available for this, but you can just use a mix of PVA glue and water (or neat PVA if it's really greasy) - this is easier to use than oil based alternatives. This will also bond well to the brick surface and make it possible to paint them with regular emulsion paint (though you'll get a more durable finish with a masonry paint)
2006-09-08 03:35:12 · answer #1 · answered by Tom W 2 · 0⤊ 0⤋
the best option would be to take em off and tile the area, but if that's not what you are up to, I would say, use an orange based degreaser first. Id wash and rinse it a couple of times according to the directions. Also, prime them. Ask a 'pro' at whatever paint shop you go to. Tell them the material the 'bricks' are made of (some are plastic, some are actual thin bricks) they will direct you to the best primer and paint, oil vs water based. You will want a sheen on the paint so its easy to clean, being in the kitchen and all.
Happy painting!
2006-09-08 20:21:00 · answer #2 · answered by ShaMayMay 5 · 0⤊ 0⤋
the best thing to do here is clean the brick effect tiles down first using sugar soap (remember to rinse well ) then use a stainblocker you'll get quick drying ones from all leading paint suppliers this part only needs to be done to the dirty areas then you can use any kind of paint you like as its indoors and not outside so theres no need for masonary although it wont do any harm if you choose to but as you are having these problems with dirt either a silk or soft sheen or any paint washable would be advised
2006-09-10 19:26:51 · answer #3 · answered by poker_player2000 1 · 0⤊ 0⤋
Use very hot water with Sugar Soap (available at DIY stores) don't be too harsh when you wash but wear rubber gloves and use a scrubbing brush. Leave to dry for a few days and you will see the bricks change colour as they dry out.
apply a PVA base coat before applying emulsion just in case any residue bleeds through. It will takes a while because you should wait for the surfaces to dry between coats
2006-09-10 13:07:52 · answer #4 · answered by Anonymous · 0⤊ 0⤋
wash with a brush and sugar soap. then treat the brick tiles with stabiliser. you can aquire this from b&q. Apply with a cheap brush as it will harden after use. this will seal the bricks,and will stop any residue from within the tiles bleeding through after painting.you will find that you will less paint as the the pours of the bricks are sealed.what type of paint is up to you some like masonry and some like gloss. its all down to preferance. if you use oil based they will be easier to clean. as chalky paints mark easier and usually leave scuff marks after cleaning
2006-09-11 16:13:23 · answer #5 · answered by aaron 1 · 0⤊ 0⤋
Hot as you can handle water, and lots of soap will clean them well enough. But do a good job.
Then, using a "light grade" sandpaper, rough up the surface a little to give the paint something to stick to.
2006-09-08 10:21:56 · answer #6 · answered by D 4 · 0⤊ 0⤋
Clorox Spray cleaner is probably going to be the best at reducing the grease
2006-09-08 10:21:23 · answer #7 · answered by Anonymous · 0⤊ 0⤋
Clean it first by using vinegar, that will take the grime away and give you a clean surface to paint on.
2006-09-08 11:13:52 · answer #8 · answered by Lisa T 2 · 0⤊ 0⤋
if the tiles are brick then use masonary paint
2006-09-08 10:20:07 · answer #9 · answered by Anonymous · 0⤊ 0⤋