What is a "locking differential?"?

Question

This seems to be an option when I purchase a vehicle. Do I need it?

Answer 1

A differential is the set of gears that converts rotation of the drive-shaft to rotation of the axles and wheels. It is the big round thing in the middle of the rear end. A locking differential allows power to go to both wheels at the same time verses limited or variable slip differentials which may only transfer power to one or two wheels depending on need.

Answer 2

It's more likely a "limited slip" differential as opposed to a true locking differential. Some 4WD vehicles have a locking diff between the front and rear to improve traction on slippery surfaces. Otherwise, true locking diffs are strictly for racing.

A normal diff sends the power to the wheel with the least amount of traction. Limited slip diffs send it to the wheel with the most traction to minimize wheel spin either on slippery surfaces or under hard acceleration.

The differential is needed because when the vehicle turns, the wheels in the inside of the turn rotate more slowly than those on the outside of the turn. The diff allows the wheels to rotate at different speeds.

A true locking diff does not permit the wheels to rotate at different speeds and is only useful for drag racing or possibly off-road use in limited cases.

Most vehicles will do fine without the limited slip differential. Limited slip diffs have clutches that need periodic replacement. When the clutches wear out, it behaves like a normal diff and any benefit is lost.

Very few drivers properly maintain a limited slip diff, as it doesn't give much in the way of noticeable symptoms when the limited slip feature is lost. A limited slip diff can also cause unpredictable handling when driving twisty roads at high speeds. An expert driver can deal with this, but most drivers are nowhere near expert -- myself included, and I have well over a million miles under my belt.

Answer 3

When a car goes around a corner, the outside wheel turns faster than the inside wheel. This is made possible by the 'differential' which allows one wheel to turn faster than the other. The problem with this is, if one wheel starts to slip on ice or wet pavement, it get's all the power and will just spin. To correct this problem, some car builders offer a "locking differential" so the loose wheel won't spin.

Answer 4

a locking differential is just what it says, it will lock both drive wheels together to allow for more traction but yet allows it to slip for better drivability when your taking your vehicle on surface streets. it isnt needed if it never is going to see off road or snow. now if you go into the mountains, deffinatly get that option. you will be thankful
you can also leave to black marks instead of one ;)

Answer 5

I don't know where you live but if ur handle is true I would definitely say no. It is to manually put ur vehicle in 4 wheel drive. Now if you go up to the mountains skiing or somethin like that where you have a chance of driving in MEASURABLE snow I would say go ahead

Answer 6

Having one, you will never get stuck in mud or snow, with one drive wheel stopped and the other one slipping like crazy..

Answer 7

Locking differential
From Wikipedia, the free encyclopedia

A locking differential or locker is a variation on the standard automotive differential. A locking differential provides increased traction compared to a standard, or "open" differential by disallowing wheel speed differentiation between two wheels on the same axle under certain conditions.

A locking differential is designed to overcome the chief limitation of a standard open differential by essentially "locking" both wheels on an axle together as if on a common shaft while still allowing them to rotate at different speeds when it is required (such as when negotiating a turn). This forces both wheels to turn in unison, regardless of the traction (or lack thereof) available to either wheel individually. An open differential will cease the transmission of torque to one wheel if the opposite wheel has little or no traction. This may occur if one wheel comes into contact with mud, snow, or ice, or if the wheel is somehow removed from contact with the road after encountering an obstacle or area of soft ground. In such a situation, an open differential will continue to spin the wheel with the least amount of traction but will transmit little or no power to the wheel that has more solid traction. Basically, it will transmit only as much torque to both wheels as the wheel with the least amount of traction can sustain. This can result in the vehicle failing to deliver enough torque to the drive wheels to keep the vehicle moving forward, at which point it will be stuck. A locking differential solves this problem with its capability of delivering 100% of available torque to the wheel with the most traction.


Types

There are two main types of lockers: automatic and selectable.

* Automatic lockers lock and unlock automatically with no direct input from the driver. Some automatic locking differential designs ensure that engine power is always transmitted to both wheels, regardless of traction conditions, and will "unlock" only when one wheel is required to spin faster than the other during cornering. They will never allow either wheel to spin slower than the differential carrier or axle as a whole. The most common example of this type would be the famous "Detroit Locker," also known as the "Detroit No-Spin," although there are many others. Other automatic lockers operate as an "open," or unlocked differential until wheelspin is encountered and then they lockup. This style generally uses some type of internal governor to sense a difference in wheel speeds, or they react to torque input from the driveshaft. An example of this would be GM's "Gov-Lok." This is the type most often found on vehicles factory equipped with a locking differential.
* A "selectable" locker allows the driver to lock and unlock the differential at will from the driver's seat. This can be accomplished via compressed air (pneumatics) like ARB's "Air Locker," electronic solenoids (electromagnetics) like Eaton's "ELocker," or some type of cable operated mechanism as is employed on the "Ox Locker." This allows the differential to perform as an "open" differential for improved driveability, maneuverability, and reduced tire wear, while also having full locking capability for ultimate traction when it is desirable or needed. This is really the best of both worlds, but selectable lockers are more complex, and therefore more expensive, than their automatic counterparts. Some people also feel that this added complexity reduces their overall strength and durability and requires increased maintenance over the long run.



Disadvantages

Locking differentials do have some disadvantages. Because they do not operate as smoothly as standard differentials, they are often responsible for increased tire wear. Some locking differentials are known for making a clicking or banging noise when locking and unlocking as the vehicle negotiates turns. This is annoying to many drivers. Also, some locking differentials can affect the ability of a vehicle to steer in some situations, especially when the locker is located in the front axle. They are also capable of subjecting the axle shafts to much higher torque loads than would be possible with an open differential because they allow 100% of the available torque to carried by a single axle shaft as opposed to being divided up between the two. Under extreme conditions, this can cause an axle shaft failure.

Except for the added stress on axle shafts, these disadvantages primarily apply to automatic lockers, and can be mitigated, to some degree, by proper maintenance and setup. Tire wear can be minimized by ensuring that the tires are properly sized and inflated. Steering difficulties can be mostly eliminated by selecting modern lockers which are better engineered than earlier versions which were notorious for steering difficulties. Driving habits, vehicle weight, and tire size can also have an effect on the behavior of a locker.

Limited slip differentials are considered a compromise between a standard differential and a locking differential because they operate more smoothly, and they do direct some amount of torque to the wheel with the most traction, but they are not capable of 100% lockup.

Applications

* Race cars often use locking differentials in order to maintain traction during high speed maneuvers or when accelerating at extreme rates.
* Some utility vehicles such as tow trucks, forklifts, tractors, and heavy equipment use locking differentials to maintain traction, especially when driving on soft, muddy, or uneven surfaces. Lockers are common in agricultural equipment and military trucks.
* Four-wheel drive vehicles that drive off-road often use locking differentials to prevent from getting stuck when driving on loose, muddy, or rocky terrain. Locking differentials are considered essential equipment for serious off-road driving.

Retrieved from "http://en.wikipedia.org/wiki/Locking_differential"

Category: Automotive transmission technologies

http://en.wikipedia.org/wiki/Locking_differential

Answer 8

not terribly important unless you gonna drive like a rally pro in the dakar

Answer 9

Only if you need true four-wheel drive.

Answer 10

If you live where it snows or is muddy it will help., but if you stay on highways it's useless.