On her driver side the cv joint was clicking and it finally gave out. She has not got much money. Is this kinda hard to fix or easy. Can ayny one give me some easy directions I have a jack and some old tools. Thanking you ahead.
2007-12-07 08:34:57 · 8 answers · asked by J R 4 in Cars & Transportation ➔ Maintenance & Repairs
Remove the wheel, then the big nut holding the axle into the spindle.MAke sure the axle can now be pushed inboard fairly easily, or at the least spray penetrating lube onto it and tap it in as far as it will go.
Remove whatever is holding the lower control arm to the spindle, usually a nut, or a nut and bolt, and pry the lower control arm down, freeing it from the spindle. Swing the spindle outbord, while tapping on the axle to free it completely from the spindle. Note how far into the transmission the inner cv joint goes.
Now comes the hard [art-getting the axle out of the transmission-its held in by a spring-loaded c-clip, and usually has to be pryed/popped out of the tranmission by prying /tapping the inner cv joint housing.
Installation is doing everything the reverse, just make sure that the new axle goes in AT LEAST as far into the transmission as the old one was.
Not a real hard job-here in the shop the job avaerages about 20 minutes.
2007-12-07 08:49:15 · answer #1 · answered by ruskinflgator 5 · 0⤊ 1⤋
i just changed the one in my honda if its anything like that it was simple.. take the tire off ... take the spindle nut off. take the arm loose... and take it loose from the ball bearing and the axle will slide right out. My axle didn't cost but 60 bucks and it was a whole lot easier than i thought.... you might have to rent the tool to take the spindle nut off... costed $50 but they give you that back when you take it back and there will also be a core charge on the axle.
2007-12-07 16:51:49 · answer #2 · answered by chelle B 4 · 0⤊ 1⤋
Sometimes you need special tools to remove cv's, tools you'll have to order. Look around, you may be able to find someone who knows what they're doing to do it for ~$175, depending on your area.
2007-12-07 16:49:08 · answer #3 · answered by geezuskreyest 5 · 0⤊ 0⤋
u have to break that axle nut which is really on their best done with an airgun... but u can do it by hand i believe its a 32 mm socket or 36 after that take tire off ....disconnect tierod end...and the strut....pull it out be careful of your brake line....after u clear everything tie it up so its not hanging by the rubber brake hose....have to work the axle out then....the end near the trans u pop out with a big screwdriver....good luck
2007-12-07 16:49:40 · answer #4 · answered by george_12050 1 · 0⤊ 1⤋
If you don't know what you are doing.....don't do it. It isnt that expensive to have done correctly at a shop. Many will tow the vehicle there if needed. To attempt this job could result in damage to you and the car.
2007-12-07 17:02:20 · answer #5 · answered by Otto 7 · 1⤊ 0⤋
You may need more than a jack and a few tools to fix that
2007-12-07 16:38:31 · answer #6 · answered by Anonymous · 1⤊ 1⤋
I heard there was a recall on those...maybe the dealer will fix it
2007-12-07 16:37:56 · answer #7 · answered by Lydia 3 · 0⤊ 0⤋
replace the whole axel really not that much if she cant afford that then why is she even driving??
2007-12-07 16:41:05 · answer #8 · answered by redhonda00 1 · 1⤊ 1⤋