2007-11-18 13:06:14 · 11 answers · asked by michaelsan 6 in Home & Garden ➔ Do It Yourself (DIY)
I thought I remembered but forgot! I only have 90 corners and on a horizontal plane, but I can't get it right. Can anyone help?
2007-11-18 13:19:11 · update #1
There really is no easy way. Too many selections and angles to chose from. I hate to tell you,,,but there rarely is a 90 degree angle in a house. If you can afford it buy about a total of 6 feet (2 pieces 3' long) try cutting it @ a 33 degree angle on the miter tilt (when you tilt the blade on the saw) and a 32.5 degree on the miter cut (the angle you cut moving the table angle) This is only if you are using a Compound miter saw. You will have to adjust the blade from there weather to much of an angle or to little. If you are not using on or can not get a hold of one you will be better off using decorative inside and outside corners so you do not have to cut angles at all.
2007-11-18 15:19:01 · answer #1 · answered by Da Spurs 2 · 1⤊ 1⤋
If the room has outside corners, the crown molding will have to be mitered for an outside corner.
Experts recommend sawing the molding upside down. Think of the bed of the saw as the ceiling and the fence is the wall. You may want to clamp a guide to the saw bed to keep the molding at the correct angle and prevent any twist as you apply pressure with the saw blade.
- See more at: http://www.miconstruguia.com/en/how-to-cut-crown-molding/
2014-07-26 16:24:13 · answer #2 · answered by Misty Blue 2 · 0⤊ 0⤋
I just received a note from Steve in NC,,,one of OUR PEERS. The notion is multiple angles and Flipping; but he offered a "TOOL" I intend to try. I don't have the Q at hand but look him up, he is also a GC. 20 years. I suggest you check him out as well.
Steven Wolf
I have to tell you however. He and I agree on one thing. We dislike Crown molding.
2007-11-18 15:31:06 · answer #3 · answered by DIY Doc 7 · 1⤊ 1⤋
I have installed a lot of crown over the years. The thing to do is pretend the base of your miter saw is the ceiling, and the fence is the wall. place the crown in your saw, just like you would on your wall.
2007-11-19 05:10:46 · answer #4 · answered by shawnd518 5 · 1⤊ 1⤋
A good miter saw will have the angles marked. You don't use 45 degrees. You lay stock flat and use indicated marks on the saw. Keep scrap piece of each angle in your pouch for easy reference.
2007-11-18 13:59:06 · answer #5 · answered by pumpdatiron 6 · 1⤊ 1⤋
Here's a good video on that
http://www.askthebuilder.com/How_To_Cut_Crown_Molding_Video.shtml
The trick is realizing whether the joint will be on the inside or outside of a corner and to remember which edge is up. All that is covered.
2007-11-18 13:08:34 · answer #6 · answered by Rich Z 7 · 1⤊ 1⤋
When you trim a door with casing the 45 angle has the long cut of the angle is on the top.The short is on the bottom.Crown is the opposite.The long part of the 45 goes on the bottom.The short part of the angle goes on top.
2007-11-18 13:17:50 · answer #7 · answered by snowman 5 · 1⤊ 3⤋
It's tuff to startoff.
Can you think upside down, and backword's ?
2007-11-18 13:38:28 · answer #8 · answered by jacksparrow 3 · 1⤊ 0⤋
Here is another one.
http://www.rd.com/familyhandyman/content/17453/3/
2007-11-18 13:17:12 · answer #9 · answered by Michael C 5 · 1⤊ 2⤋
"Measure twice, cut once." First rule of a tradesman. <};-})
2007-11-18 13:10:15 · answer #10 · answered by Anonymous · 1⤊ 2⤋