how hard is it to take out a bathtub to replace subflooring that is rotted access to tub is pretty good has 3 sided tub surround
2007-11-08 08:11:54 · 11 answers · asked by feiheck 1 in Home & Garden ➔ Do It Yourself (DIY)
I will give you the benefit of 20+ years of experience in construction. Unless you are very handy, or have a friend(s) that are, you are better off leaving this one to a pro. I'm not saying you can't do it - because you have got some good advice here on how to do it. But this is a major undertaking and the tub is incredibly heavy.
I think Doc's advice about doing it "sectionally" is really sound advice. If it was me that's the way I would do it. Whatever you do - good luck!
2007-11-08 08:57:23 · answer #1 · answered by Steve in NC 7 · 2⤊ 0⤋
Removing A Bathtub
2016-10-02 13:10:48 · answer #2 · answered by pazo 4 · 0⤊ 0⤋
This is a fairly extensive job. to remove the walls of the tub you will have to remove approx. 3 to 6 inches of the wall covering that surrounds the tub walls. If it is drywall, this will be fairly easy. This will show you how the tub walls were mounted, by nails or screws, etc. If they were nailed there is a chance of damaging the fiberglass when removing them. After you remove the tub walls just remove the drain from the bottom of the tub and pull it out. Do what you need to and put it all back together. I would put the tub walls back up with screws to make it easier in the future if need be. The only other option would be dependent on whats under the tub. If the tub is on the second floor you can get to the underside through the ceiling. This would probably be less extensive than removing the tub walls. I hope this helps you on your journey. Good luck...
2007-11-08 08:27:10 · answer #3 · answered by happygolucky 4 · 0⤊ 0⤋
Well the surround probably has to go. I assume you notice that a usual TUB fits pretty tight; within fractions to a space approx 54 inches in length. Then certainly there is the issue of what else in the bathroom might be in the way; IE: Toilet.
I'm not a Physics genius, but considering the usual depth of a tub you can't exactly angle it UP out of the way, initially to remove in from a usual bathroom.
I've never quite understood the inane practice of FITTING a tub; and NOT considering ( by a contractor) that one day it might be something to change.
I suppose with some tedious effort you could JACK it/ lift it and replace the sub floor sectionally. I suggest double concrete backer board sealed, and check the beams for rot/damage.
The invention and intent of the claw foot tub was far evolved for its time. I wonder why we regressed in thinking???
Steven Wolf
2007-11-08 08:22:35 · answer #4 · answered by DIY Doc 7 · 3⤊ 0⤋
It's much more difficult than it looks if you want to re-use the tub. For whatever reason, tubs are installed in the tightest possible spot most of the time. However, it may be possible to jack the tub up and replace the subfloor.
2007-11-08 08:45:22 · answer #5 · answered by Anonymous · 0⤊ 0⤋
I how it's not a cast iron tub for your sake. Heavy isn't even the word! Also, is there tile butted up to the tub, if so, you'll probably rip some of that away in the process. It there a sliding door that has to come out too, especially if its connected to tile? This question really depends on all the details only you know about.
2007-11-08 12:59:55 · answer #6 · answered by 80's kid 6 · 0⤊ 0⤋
You will need to disconnect the water supply pipes and the drain. There is a flange around the edge of the tub that extends up about 1/2". The wall board sits on the inside of it. This will need to be cut. It was installed before the walls so it will be a tight fit trying to slide it out. May also be screws or nails through the flange and into studs.
2007-11-08 08:22:56 · answer #7 · answered by sensible_man 7 · 1⤊ 0⤋
If the subflooring is rotten , chances are you may have rotten beams as well
Best bet
No short cut
Take the whole lot out and do a good job
If the hot and cold have stop cocks--close off and remove bath
If no stop cocks then either shut the water off or freeze the pipes and remove
Dont forget to close off pipes while you are working
Simple plastic stop ends will do
Bathroom Fitter
2007-11-08 08:48:13 · answer #8 · answered by Jeffus 1 · 0⤊ 0⤋
no-one has mentioned it yet so I will.All good advice,but if you only want to remove the subfloor in the bathroom and not under the tub,you can patiently chisel along the tub and remove the rest of it.but if its rotted underneath,then you better get a pro
2007-11-08 10:26:57 · answer #9 · answered by ben s 4 · 1⤊ 1⤋
With experience, it's a pain in the butt.
No experience could be a disaster waiting to happen
Lowe's books on plumbing would help.
If U have a friend with a little framing or some kind of construction experience might help
2007-11-08 08:23:18 · answer #10 · answered by Anonymous · 0⤊ 0⤋