we are currently installing a kitchen island in a loft apartment and we are not sure if the front panel of the island should be screwed on or glued on. The lowes guy is going to glue the formica counter top to the island but what about the front?
2007-09-11 12:50:00 · 10 answers · asked by n50plic 1 in Home & Garden ➔ Do It Yourself (DIY)
I used Locktite construction adhesive on mine. It gives you the fastest grab, eliminates the necessity of screws and nail holes to fill and gives a cleaner look. Lowes sells it, just make certain that you have good coverage and if the front panel is slightly warped or not completely level, rig up a clamp system to hold it in place until it dries. (We used extension clamps hooked together.)
2007-09-11 13:26:21 · answer #1 · answered by eskie lover 7 · 0⤊ 0⤋
Depends on whether you need access from that side, into the island (some islands have sinks, and you need to be able to get to the plumbing, for example)
If there is no access required, then you can do it either way. I would suggest that if you're going to glue, then use a construction adhesive, and pin nail the panel in place. The pin nails will hold the panel until the glue sets.
Have Fun
2007-09-11 13:01:00 · answer #2 · answered by thewrangler_sw 7 · 0⤊ 0⤋
I'll just add my two cents, having a couple of years in the process. BRAD GUN the paneling to the faces of the Island.
Assume for just ONE moment that something damages the paneling, or as many humans do, you decide on CHANGE at some point.
Certainly you can get a tube of liquid nails and do drops of adhesive on key spots, but it need not be broadcast spread like the contact cement will be on the Mica.
Steven Wolf
BTW, installing paneling in a room, isn't usually done with glue.
2007-09-11 13:56:46 · answer #3 · answered by DIY Doc 7 · 2⤊ 0⤋
It depends on a couple of things......
First: What's the panel made of Formica or plywood
Second: How thick is it?
Now if it's Formica 1/4" or less......"GLUE" 1/2" or thicker.....Screws through the back side of the panel from the inside of the island......
If it's plywood glue and brad nailer.....
2007-09-11 18:40:01 · answer #4 · answered by adevilchild38 5 · 0⤊ 0⤋
The company that made your cabinets will have accessories to match. I purchased a sheet of thin wood and used it to slip into the groove of the door in my dishwasher so it was the same wood finish as the cabinets. I realize the front of a dishwasher is smaller than your island, but perhaps if you can get a hold of several sheets you can abut them to some trim work. Another option would be to wainscot the island and stain or paint it. A lot of kitchen designs today have an island with a different finish from the cabinetry. This is quite appealing as not to have the cabinetry be repetitious.
2016-05-17 10:02:35 · answer #5 · answered by ? 3 · 0⤊ 0⤋
Hi...you can use "paneling" glue by liquid nails it's found in the paint department at Lowe's....use that and then for the corners use a decorative molding which can be adhered with liquid nails as well....that's found in the molding ailse with doors and windows....good luck..sounds awesome
2007-09-11 14:31:01 · answer #6 · answered by fastjeepchick 2 · 0⤊ 0⤋
It should also be glued on.
Spend a little extra and get the best glue available.It will pay off in the long run.
2007-09-11 13:01:55 · answer #7 · answered by sonnyboy 6 · 0⤊ 0⤋
I would glue it because you would see the screws if you screwed it in. Just be sure to use a good adhesive.
2007-09-11 12:54:56 · answer #8 · answered by The Not-Know It All 3 · 0⤊ 0⤋
Informative answers, just what I was looking for.
2016-08-24 15:32:27 · answer #9 · answered by Anonymous · 0⤊ 0⤋
It should be stapled or air nailed
2007-09-11 13:53:52 · answer #10 · answered by Anonymous · 1⤊ 0⤋