English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

2007-09-05 14:38:27 · 12 answers · asked by Johnny Bond 1 in Home & Garden Cleaning & Laundry

12 answers

Spread a thick layer of fresh sawdust or kitty litter over the grease to absorb excess grease or oil on the surface

Allow the sawdust or kitty litter to sit for a day or two.

Gently sweep away the dirty sawdust or kitty litter.

Pour dry cement over the entire dried grease spot.


Allow the cement to sit for a day or two.


Gently sweep away the dirty cement.

Gather dirty cement in a bag and throw it away. Do not allow the dirty dry cement to go down the sewer.



The kitty litter and sawdust soak up grease on the surface, whereas the dry cement actually absorbs the stain out of the driveway.
For best results, clean up grease stains as soon as they happen.
Avoid further staining by using large automotive drip pans for vehicles that leak.
Make sure the forecast is clear for the days you'll be using dry cement on the grease spots if they are outdoors. Dry cement and water will create hardened concrete

2007-09-05 14:49:42 · answer #1 · answered by Anonymous · 1 0

take cat litter the clay stuff and walk on it to scuff it in. Then take a coarse broom an sweep the dust and pieces all over the oil spot then sweep it off the spots and check for remaining spots. You just keep sweeping until the spots are gone. I have cleaned many an oil spotted floor that I couldn't get wet. Mechanic and pump Jockey

2007-09-05 14:50:44 · answer #2 · answered by redd headd 7 · 0 0

in case you basically spilled it, sand, kitty muddle or sawdust could desire to do the trick... however the longer you enable it seep into the concrete, the harder that's going to be to get it out. If it extremely is been greater advantageous than 6 hours through fact the spill, solid good fortune getting something again up. next time you recoat your storage floor, attempt a sealant. once you seal the concrete, not something would be waiting to seep throughout the time of the sealant into the concrete.

2016-10-18 02:15:19 · answer #3 · answered by ? 4 · 0 0

Use oil dry or cat litter pour it on and step on rub it in with body weight let set then sweep of

2007-09-05 14:52:09 · answer #4 · answered by nightdancer62 2 · 0 0

I use oil dry, which you can get almost any hardware store. Also, saw dust works just as good, if you have access to some of it.

2007-09-05 14:44:59 · answer #5 · answered by nate_b_25_2000 2 · 0 0

if it's cement you'll never get the stain out, but to soak up the oil, go to a auto parts place and get oil absorbant like "gator"

2007-09-05 14:44:19 · answer #6 · answered by w00189wr 4 · 0 0

Clay cat litter or cedar bedding for rabbits etc....soaks it right up than sweep it up and dispose of in proper manner.

2007-09-05 14:44:52 · answer #7 · answered by waterlover 4 · 0 0

USE KITTY LITTER TO ABSORB THE OIL, THEN YOU DAWN LIQUID SOAP AND WATER AND BROOM CLEAN IT

2007-09-05 14:44:01 · answer #8 · answered by whateverbabe 6 · 1 0

oil dry works well.

2007-09-05 14:44:30 · answer #9 · answered by nvrrong 5 · 0 0

kitty litter will do the trick

2007-09-05 14:44:24 · answer #10 · answered by talk2bobbie 3 · 0 0

fedest.com, questions and answers