I want to add memory to my TARGA PCX3200 computer It has 512mb DDR & I want to double this.?

Question

Will any 512mb DDR fit. Or is there specific memory for different computers. Also can you tell me how to install it.

Answer 1

Go to http://www.crucial.com , and press "Scan my system".
It should tell you what RAM to get. For example if it's DDR1 PC3200, then in the store make SURE it has DDR1 PC3200.
Or if you don't want to do with that website, just open up your computer and see the reference on the RAM.
Here's a video on how to install RAM:
http://www.youtube.com/watch?v=SiFIgSQOY7g

Answer 2

You should match the memory you have for best results. i.e. if you have DDR 3200 memory, you should get DDR 3200 memory. It's not all the same. I believe that someone else discovered that your system comes with a single 512 bar. So you should just get a second.

To install it, you first need to shut down and unplug your system. And yes, you should physically unplug it. Next you will need to figure out how to get into the case. Different cases have different ways to get in it. You might find a couple of screws on the back side that need to be unscrewed or there may be a tab to pull. Can't really help you here. You will just have to figure that part out but don't stress on it, they usually make it easy to get in the case. Oh, you should do this on your kitchen floor. Basically, just get off of your carpet as you can pick up a static charge. Next ground your self with a grounding strap or just touch the metal housing of the computer. Now you are ready to work.

Locate your memory slots. There should be 4 of them right together. Since you are just going to add a second bar, you will need to figure out which slot to put it in. Since you have 4 slots, these are paired in banks numbered 0 and 1. With each bank having 2 slots, A and B. You will need to locat bank 1 slot A and install it there.

---B0-----------B1---
S1 - S2 | S1 - S2
Target this ^

So after you are done, you will have an empty slot between the installed memory.

Next, you will notice that there are retaining clips on each side of the memory bar. Just push down gently on each one of these and it will release the memory. Note, since you are just going to add memory and not replace it, then this step will probably not be necessary but you should make sure that before you insert your new memory, those little clips are in the open or spread position. Not vertical.

Now, orient the memory. You will notice that there is small slot in the bottom of the memory (there may be 2) you will need to line this up with memory slot. If it doesn't look like it will fit, then turn it around and try again. After you have it oriented correctly, gently press the memory into the slot. It should snap into the clips when you have it right. It will take a small ammout of pressure to do this. Just don't force it. Just make sure that you have everything lined up.

Next, put your case back together and make all your connections in the back. Turn it on. You will know if you did something wrong by listening for beeps when it boots. One beep good. Two beeps bad. If you get two beeps, then go back in there and reseat the memory and try again. Also make sure that you have the right type of memory.

Good Luck.

Answer 3

Using Internet Explorer visit www.crucial.com (it doesn't work very well with Firefox...)

It will ask you to download and run a small application that will scan your system and check the current status of your memory.

It will report on what you have at the moment and the recommendations for upgrade.

You may discover that your existing memory is of a slower rate than what they are recommending. Always go for the faster memory.

If you have the cash, buy 2x 512MB DDR sticks of memory and install them. Using the anti-static bag and the box that came from crucial (or eBay if you decide to go there), pack up the existing 512MB and sell it on eBay. At least you'll get something for it...

Or buy one and sell the slow stick on eBay. When you get the money for that stick, put it towards a second fast stick.

Answer 4

I think you have some superstitious people answering your question. You need the same memory configuration (DDR in your case) or the memory won't fit, let alone work. All the memory operates at the speed of the lowest speed module so your new 512Mb module needs to be as fast or faster than your old one. It's sometimes cheaper to buy faster. The new memory does not have to be from the same manufacturer.

Answer 5

According to article below, your Motherboardd has 4 DIMM style memory slots and comes fitted with a single 512Mb module ("Swissbit")

It might be a good idea to check this is correct by inspecting your motherboard ..

To double your memory, you need to purchase a second identical module (i.e. DDR400 512Mb).

Answer 6

You need to know your DDR Speed Is.

Do A Google Search For 'Cruical'

You need to look for something like 'PC5300' Ect. on Crucial.com.
(after the scan, its on the left hand side)

Email Me What your Speed Is. Or What Mobo you have, and i'll guide you all the way !

Answer 7

Go to the following link, http://www.crucial.com/uk they can do an on line check which will determine which ram your motherboard supports. They will recommend the optimum amount. You can order on line and although they are not the cheapest it is worth paying for good ram. They guarantee compatibility with your motherboard and give an excellent warranty.They lso give fitting instructions. I have used them many times and always been satisfied. Hope this helps.

Answer 8

you can check what type of ddr is installed in your memory slot,.(PC400, PC533, etc...), you must also consider the manufacturer in order to run it properly because it will result to error when loading windows, or booting malfunctions due to different manufacturers name.

Answer 9

if you don't know go to some who does cos you will end up screwing you're pc up any advice given by this means isn't always easy to exact out

Answer 10

go to the curcial website and do a scan and it tells u whats compatiable with your pc