The problem is that the stopper plug doesn't return directly in the hole immediately after a flush. I tried shortening and lengthening the chain, to no avail. To fix the problem each time, I have to reach into the tank and place the stopper plug directly into the hole. Why can't it do that on its own? How can I fix it?
2007-08-01 02:07:05 · 10 answers · asked by Maggie82 2 in Home & Garden ➔ Maintenance & Repairs
If you've tried adjusting the chain, the next step would be replacing the flapper. (That's the part you're referring to as the stopper plug,)
Sometimes flappers just don't seal well when they get old. The rubber can get stiff or brittle. Sometimes, especially on cheap flappers, the chain can snag on itself when you flush.
Turn off the water to the toilet, pull off the old flapper and chain, and take it to the hardware store. A new flapper won't cost more than $5. The job shouldn't take more than an hour.
2007-08-01 02:23:09 · answer #1 · answered by Odie D 1 · 0⤊ 0⤋
1. lift (remove) the cover on the water tank 2. if there's a ball float attached to a metal rod, lift it (very gently) and see if the water shuts off. If the water shuts off when you lift the ball all you need to do is adjust the ball float. There's 2 ways to do this. 1-where the metal rod is attached to the valve there's an adjustment screw, just tighten it down a bit. 2, bend the metal rod down (in an arc) about an inch, but DO NOT apply any pressure to the point where it connects to the valve, or you will probably break it off!! Best way to do this, if you've never done it before is to unscrew the rod from the valve, bend it, then screw it back on. Should fix the problem, but if the water continues to run when you lift the ball, the entire flush valve should be replaced. (not expensive) 3. You should see a mark on the inside of the tank to indicate the best water level, it's a raised ceramic line in the tank. Adjust the flush valve to shut off the water when it reaches this mark. 4. Best option is to replace the old flush valve with a new one (the better valves do not use a ball & rod, they have an adjustable float. to replace the flush valve assembly; (you'll need a pair of 8" slip joint pliers or a large adjustable wrench) 1. shut of the water supply to the tank, then flush the toilet, hold the handle down until the tank is as empty as it can get. 2. Use a pan or small bucket, to catch the remaining water, and disconnect the water supply line at the bottom of the tank. 3. unscrew the retaining nut and remove the old valve. 4, install the new valve, and make sure the float doesn't touch the side of the tank to insure it doesn't bind. 5. reattach the water supply line, turn on the water and check for leaks at the connection point. 6. adjust the float to shut off the water at the proper level. Installation instructions are usually printed on the new flush valve container. Your cost = about $5 US.
2016-04-01 06:23:24 · answer #2 · answered by Anonymous · 0⤊ 0⤋
the fix is prob easy if you know what you are doing. It sounds like the leak is at the bottom of the tank. There is a chain that goes from the handle to the flapper at the bottom. It can be bought for a dollar and changed in just a few minutes. They wear out and have to be replaced. The chain my be getting stuck or the ears that hold it in place may be broke. Its worth spending the little money to get a new one.
2007-08-01 02:20:33 · answer #3 · answered by Leonard L 2 · 1⤊ 0⤋
The flapper is attached to the overflow pipe either by two small "ears" that fit into holes or a piece of rubber with a hole in it that slides down over the overflow tube. One of the ears may have come dislodged or broken. This will throw it off center when closing. Check your flapper to see what has happened.
2007-08-01 02:52:15 · answer #4 · answered by sensible_man 7 · 0⤊ 0⤋
Open the tank lid, and while you hear the water running, pull the float upward (gently) if its on a arm, or the black float to the left, on the grey ballcock (water fill valve)
If lifting them, stops your running water, then it has nothing to do with the flapper.
Replace the ballcock. Go to hardware store and ask for FLUIDMASTER 400A. It's the most common out there and will work in virtually any toilet in existence.
There are step by step instructions how to change it in the box. You can do it if you have any mechanical skills. all you need is a pair of pliers or channel locks.
The new ballcock should cost somewhere around 15.00
2007-08-01 02:42:22 · answer #5 · answered by -R 6 · 0⤊ 0⤋
Check the attachment of the flapper to the overflow tube/seat. You may have a broken arm on the flapper or a build-up on the ear it clips on. You can also buy a replacement flapper that includes a new mount for the flapper. It will attach on the overflow tube.
2007-08-01 02:14:16 · answer #6 · answered by Jeffrey S 6 · 0⤊ 0⤋
try cleaning the chain and the stopper this may help if not you may need a new one
2007-08-01 02:20:12 · answer #7 · answered by jim m 7 · 0⤊ 0⤋
Usually when that happens you just need to replace the whole flapper assembly with a new one. They don't cost allot and they are easy to replace.
2007-08-01 02:18:29 · answer #8 · answered by Herr Raging Boehner. 5 · 0⤊ 0⤋
check inside the tank some sediment may just have to be cleaned or the chain may be sticking.
2007-08-01 02:09:48 · answer #9 · answered by Michael M 7 · 0⤊ 0⤋
yea just go buy another petcock valve I think that's what there called and there very simple to install
2007-08-01 02:10:11 · answer #10 · answered by Tom B 2 · 0⤊ 1⤋