i had a problem with the driver front wheel, but i don't know if that one is causing the shaking/vibrating.
2007-06-10 01:49:42 · 10 answers · asked by Anonymous in Cars & Transportation ➔ Maintenance & Repairs
Usually when that happens that means that the tires are not properly balanced.
2007-06-10 01:52:47 · answer #1 · answered by ncbrave25 3 · 1⤊ 0⤋
Look Guy's he had problems putting it on. Please do not drive until you do two things jack up both wheels in front carefully not on the aluminum oil pan. place two jack stands apply the parking brake. Make sure the wheels turn freely then start the car and put it in gear. With the wheels spinning looks for wobble not bolted on properly or excessive up and down side to side motion in the rim or tire. Second thing is to remove the wobble rim tire assembly take it to a tire shop for additional tire or rim replacement. Could be a bad tire or a rim that center or bolt pattern is not the same as the others. I have even seen defective rims where the bolt center was off by 1/4 inch. You can even put one of the old rims back on to drive over to a tire shop. I use a Hunter GPS 9700 road force tire balance dynamic balance wheels you should insist on dynamic balance/ road force test.
2007-06-10 09:12:23 · answer #2 · answered by John Paul 7 · 0⤊ 0⤋
possibilities for vibrating steering:
1. wheel bolts not tight enough, especially on one side.
2. Tyre has broken some inner steel bands. Switching both tires left to right will prove this theory.
3, tire not balanced, but this will only vibrate at higher speeds..40 - 60 mph. The test to prove this, is to put front tires on the back, and back on the front. tighten bolts correctly, drive 60 mph.
4. Your brake rotors are not flat and perfectly straight, and your foot pedal and wheel will vibrate when you apply the brakes.
5. Your INNER driveshaft bearings are worn out, Not the outer CV joints. Vibrations at higher speeds.
2007-06-10 09:03:29 · answer #3 · answered by Anonymous · 0⤊ 0⤋
If the new wheels are custom, you most likely didn't put hub rings on when you installed them. Most common source of vibration, and cheap to fix with a set of hub rings at $20.
2007-06-10 10:11:16 · answer #4 · answered by ladybugewa 6 · 0⤊ 0⤋
Take your wheels to a tire shop and have them balanced. If you are still having the vibration it could be a tire, or something in the suspention.
2007-06-10 09:00:26 · answer #5 · answered by thepitboss 3 · 1⤊ 0⤋
Put tires on them! just kidding. If they were balanced and you put them on yourself, you may have misaligned lug, usually caused by not understanding there is a lug tightening sequence. One tire could be out of round. If you bought the wheels used one or more could be bent or warped. If they had tires on them and you bought them used one or more balancing weight may have fallen off.
Hope you find a resolve with the above,Good luck.
2007-06-10 09:06:34 · answer #6 · answered by bob D 3 · 0⤊ 0⤋
Wheel and tire out of balance. Have them balanced by a shop with a balancer.
2007-06-10 08:59:35 · answer #7 · answered by ThisJustin 5 · 1⤊ 0⤋
All tire must be balance after mounting take it to a tire shop that sells the brand name of tire that you mounted and many will balance for free or at a discount either way you must have them balanced.
Good luck
2007-06-10 09:04:26 · answer #8 · answered by ASmiles1 4 · 0⤊ 0⤋
TRY INSPECTING THE TIRE FOR A BUSTED BELT.JACK THE CAR UP SECURE WITH JACK STANDS,SPIN WHEEL TO SEE IF RIM IS BENT OR NOT INSTALLED CORRECTLY.OR HAVE THE WHEELS BALANCED.
2007-06-10 09:18:47 · answer #9 · answered by Anonymous · 0⤊ 0⤋
Sounds like your tires aren't balanced....this is why you take it to a professional who has the diagnostic equipment to do the job right.
2007-06-10 08:58:18 · answer #10 · answered by auntcookie84 6 · 1⤊ 0⤋