help PC maintenance!!!!!?

Question

how do you upgrade the memory on your pc?...can you do it yourself?

Answer 1

To actually upgrade the memory you will see the slots for the ram and at each end a small tab which you have to push away from the ram to unlock it, at that point you will take one end and then the other and push down on it you will notice the tabs should move in a little bit they may even lock for you, if they dot just push them towards the ram and you should be all set.

Answer 2

Upgrading memory in a PC is a very simple upgrade, provided you know a few details about your computer. First, you need to know what kind of memory your computer actually takes. An easy way to find this out is to use a program called CPU-Z. It is a free download off of www.cpuid.com. When you run the program, you will notice several tabs across the top. The first one you should be concerned with is the one called "Memory". There you can find the type of memory your computer uses. For example, mine takes DDR. The second thing you need to know is the speed that your memory runs at. The tab SPD will give the max bandwidth of your current memory. Now that you know what the type and speed of memory your computer takes, you can purchase a new module.

Also, be sure your computer actually has an empty slot for memory. If it does not, you can remove a smaller module and install a larger one in its place.

Installing memory is far simpler then matching it. First, shut down your computer and unplug it. Then (to discharge your body of static) touch a bare metal part of your computer's case. Then you must open the case. This is usually done by removing screws (usually either phillips or thum screws) from the back of the case and sliding the side off. The large circuit board in the back is called the motherboard. This is where the memory is installed. You should see similar chips to the one you bought already in slots on the motherboard. To install the chip, you pull the two (usually white) clips on the side of the slot down and out, then align the chip so the notch(es) on the contact side match up with the small plastic hump(s) on the slot. Then apply firm and even pressure to push the chip into the slot. Push until the two clips snap into place. Then put the sides back onto the case and plug it back in. Usually, no further action is required. The next time you boot your computer it will automatically identify the new memory and you should experience improved performance.

A few things to keep in mind-

Motherboards have memory limits. For example, mine has a limit of 4 GB (4096 MB). Most modern computers should have a limit of 2 to 4 GB. 32-bit Windows (most likely what you have) also has a limit of 4 GB.

Answer 3

yes u could do it urself!but u got to know what ur motherboard supports!u cannot just go to a shop and buy a 512MB 0r 1GB ram.u got to know if ur mainboard ,
1.supports ddr or ddr2 ram and
2.the fsb speed .
it is always nice to have a pair {i.e.,two 256 MB ram or two 512 MB ram rather than having a single 512 MB or a 256MB and a 512 MB ram.}
u could also scan ur system at "crucial.com".it would tell u what sort of ram u need.installing it in the slot provided on the mainboard is no matter.pls do not fear about that , pal!

Answer 4

Yes, you can install RAM by yourself. Installing RAM is one of the easiest upgrades you can do. Essentially, all you do is remove the old RAM module and plugin the new RAM module. Just be sure to buy the right RAM. RAM comes in several flavors. There is RAM for notebooks and desktops. There are different speeds. There are different number of pins...etc. Here is a how to article from PC World with step by step instructions and pictures.

"Upgrade Guide Install RAM modules step by step" --pcworld.com (http://www.pcworld.com/article/id,18024-page,1/article.html)

Answer 5

Yes you can do it yourself.

Just make sure for one thing that memory modules you buy are compatible with your motherboard. And there bus speed should match your board in order to get optimized performance.

Bring new module. Unplug the old one and Just plug in your new one.

Answer 6

You purchase a memory card and install it. So the answer is "yes", you can do it yourself.

Answer 7

Run the scan at http://www.crucial.com to identify your type, then just buy it and pop it in very simple !