i have a 1.4 GTA Metro and the clutch is going and want to find step by step insructions for free
2007-05-17 00:34:39 · 8 answers · asked by matthew b 1 in Cars & Transportation ➔ Maintenance & Repairs
Good Luck Finding a site for free. I Know of 2 different programs on the Internet but the are both really expensive we have both of them at our shop they are Mitchellondemand and AlldataPro if you have your own mechanic shop they are definitely worth the money but if you are just going to work on one or two vehicles it is not worth it. They give you all the same information as the dealrs manuals plus they give you part numbers and they give you estimated hours. They both have about the same information, it is all a mater of opinion on wich one is beter I like Mitchell but some people like Alldata better. If you are looking for a cheap program I saw one at Walmart in the cheap computer game section I don't know how good it is but it was cheap I think like around $10.
I don't think you will find any place that will give you that information for free because then all automotive shops would use it and it takes money away from people that do that job for a living. If that is your only vehicle you might just wan't to by a manual a Parts store they are prety cheap the price will still be less the the cost of labor to have someone else do it.
2007-05-17 01:51:52 · answer #1 · answered by porterc2133 2 · 0⤊ 0⤋
A Haynes manual is your best bet as they'll give you a clear, photographic, guide to the job and how to tackle it safely.
Amazon, Ebay and other similar sites will surely have a reasonably priced (though clearly not free) copy.
Though if you're not confident/experienced at car maintenance then diy could work out a false economy - you'd get a warranty on the work if done by a garage and wouldn't spoil a weekend or more lying under the car or bent double over the engine struggling without the proper tools and facilities.
2007-05-17 02:03:35 · answer #2 · answered by Anonymous · 0⤊ 0⤋
Try your local library, they usually have a good selection of the Haynes manuals.
I am not familiar with the layout of this particular vehicle, but the old metro/mini is dead easy have done them unassisted on several occasions.
Not like the old days when you had to take the engine or gearbox out!!
2007-05-17 00:45:28 · answer #3 · answered by ArskElvis 3 · 0⤊ 0⤋
like pmk stated, it's not as easy as some of the older bikes... there is a C clip (snap ring) that once removed, then a seal washer to release the pedal from the shift shaft. then there is the linkage that needs to be disconnected too. mark locations before remove for ease of re-assembly. hope that helps a bit to go along with the diagram...
2016-05-20 18:35:28 · answer #4 · answered by Anonymous · 0⤊ 0⤋
Go to Auto Zone it has info you are looking for
2007-05-17 03:22:37 · answer #5 · answered by Robert L 1 · 0⤊ 0⤋
With out a shop lift? If your young and strong no problem lots of crawing and getting up and down.
2007-05-17 00:40:22 · answer #6 · answered by John Paul 7 · 0⤊ 1⤋
my advice is to buy a haynes car book which will see you repair your car from top to bottom. sorry not a lot free any more.
2007-05-17 00:45:28 · answer #7 · answered by ¸.•*´`*♥ slender slim ♥*´`*•.¸ 6 · 1⤊ 0⤋
if your asking this you don't have the knowledge or the tools for the job
2007-05-17 00:37:37 · answer #8 · answered by 51 6 · 0⤊ 0⤋