How do I suspend a tire swing between 2 trees without damaging them?

Question

We have 2 black walnut trees with branches that run too vertical to attach any type of swing (the swing would be right against the tree), plus the branches are about 40 feet up. We were thinking about trying to do it between the 2 trees but don't want to damage them. The only plans I could find are for zip lines and entail drilling all the way through the tree. Any ideas for doing this in a tree-friendly way?

We have 2 black walnut trees with branches that run too vertical to attach any type of swing (the swing would be right against the tree), plus the branches are about 40 feet up. We were thinking about trying to do it between the 2 trees using only the trunks - not the branches - but don't want to damage them. The only plans I could find are for zip lines and entail drilling all the way through the tree. Any ideas for doing this in a tree-friendly way?

The branches are actually too high to use. We were thinking there might be a way to only use the trunks.

Answer 1

Research how that kind of tree does with stress loads. Even suspended from two branches, if one is weak, the tire could be flung free during use.

Be sure to put a saddle over the top of the branch to keep the chain or rope from cutting into it and weakening it. Most saddles I've seen are simply pieces of car tire cut with a reciprocating saw.

Carabiners clipped to the chains make it easy to add the swing but use ones rated for 150 lbs or better.

Plastic hose over the chains that suspend the tire will protect fingers from pinching.


Terrific Tire Swing by Leslie Garisto Pfaff

A backyard play idea from FamilyFun magazine
Terrific Tire Swing
An old tire, some rope or chain, a tall tree--could anything be simpler? The backyard tire swing has been entertaining kids pretty much since backyards were invented. Here's how to set one up right.

1. If possible, find a used beltless light truck tire or old tractor tire (try a junkyard or tire store). Avoid steel-belted tires, whose sharp cords might eventually work their way out of the rubber sheathing.

2. Drill holes in the bottom of the tire so rainwater can drain.

3. Choose a healthy hardwood tree such as oak, walnut, sugar maple, ash, or cherry. (Beech, while strong, has delicate roots that resent trampling.)

Materials
• Used beltless light truck tire or old tractor tire
• Drill, 1/4" and 1/2" bits
• Healthy hardwood tree
• 3/16-inch playground chain
• 2 12-inch drop-forged eyebolt, washers, and nuts
• 2 14-inch quick links
• Mulch or wood chips


Make sure the branch is straight, forming an L-shape, not a V, against the trunk, and strong--at least 8 inches in diameter where you attach the swing. It should be 9 to 12 feet off the ground (the higher the branch, the farther you'll swing). If you don't have a large enough tree, you can retrofit a wooden swing set for either a vertical or a horizontal tire swing. Complete tire swing kits are available from CedarWorks Playsets at (800) GO-CEDAR; www.cedarworks.com, or you can make your own with hardware from PlaysetParts.com at www.playsetparts.com.

4. The best way to suspend the tire (for both the swinger and the tree) is with a length of 3/16-inch playground chain. Drill a 12-inch hole through the center of the branch, then insert a 12-inch drop-forged eyebolt through the hole, securing it on top with a washer and two nuts. (If you use rope, choose nylon or Dacron. Polypropylene and hemp don't weather well, and polypropylene can also slip too easily through small hands.)

5. Drill a 12-inch hole through the top of the tire. Thread a nut, washer, and 3-inch fender washer on another 12-inch eyebolt, slip it through the tire, and thread on another fender washer, washer, and nut. Secure the chain to the two eyebolts with 14-inch quick links.

6. Spread a circle of mulch or wood chips around the trunk to protect tree roots and cushion falls.

Answer 2

Tire Swings For Trees

Answer 3

suspend tire swing 2 trees damaging

Answer 4

If the trees are 10' apart, the absolute way to not damage the trees is to get a metal swingset that you just place between the trees. You could put a 4x4 board between the trees and lag screw it into both trees which shouldn't damage them too much. Try going to a nursery and asking if something like this will damage your trees.

Answer 5

If you by (frequently or infrequently) various gardening and landscaping magazines why don’t you just acquire a total one from right here https://tr.im/5uKCj a really great resource with a tons of specifics and high quality guides , without a doubt it’s excellent value.
Ideas4Landscaping incorporate detailed diagrams and effortless to adhere to guidelines if you don’t know in which to commence , a system that is also coming with numerous themes and bonus components like the “Landscaping Secrets Revealed guidebook , Save On Energy Costs – Green Home guide or How To Grow Organic Vegetables - without a doubt a total system for the ones that want to learn landscaping or just to make the backyard or front yard far more interesting.

Answer 6

go to the store buy a half in nylon line. several feet longer that the distance between the two trees. get out your boy scout hand book and look up a pipe hitch, or any good knot that wraps around the trunk of the tree several times. Tie another piece of rope in the center between the two trees, to the one you have tied to the trees. the bottom end of the vertical rope attach the tire.