As mentioned, this is caused by moisture, and insufficient ventilation.
Alternatives are to fit a ventilation system that circulates the air better, or extraction fan that removes the moist air from the room - even a vent into the roof space will assist here.
These depend on the dynamics of the location in regards the exterior, wall/roof structures, and etc..
Some fan types are integrated with the lighting systems, which come on every time you switch on the light, and vice versa.
As for the mold, it comes off with bleach, but a more environmentally friendly solution, is to wipe it off with a cloth moistened with white vinegar. The acid within will kill the mold, even out of the grouting, and leave your tiles shiny.
Vinegar also is good for cleaning glass, and leaves it gleaming, for it cuts through the grime.
Add a little kerosene to it and it will easily remove soap scum from the shower walls as well.
2007-03-04 22:40:19
·
answer #1
·
answered by Bushrat 2
·
0⤊
0⤋
You need ventilation in the bathroom. The water from the shower isn't drying up quickly enough, causing the mold. Try keeping the window open a little and the door open when the bathroom isn't in use. You should also look into the possibility of installing a vent fan. If there is attic space above the bathroom it should be a fairly easy installation. If there is a second floor above the bathroom, you'll have to cut out the ceiling to run the vent ducts to the outside.
2007-03-04 23:57:56
·
answer #2
·
answered by bugs280 5
·
0⤊
0⤋
I installed a vent fan and tied it in to the lights system in that end of the basement. Any time that group of lights are on the fan is running. I would guess the fan runs at least 3 hrs out of every 24. After I got it clean I have had no trouble for the past 10 years. I probably remember to spray it down with some kind of cleaner a couple of times a month. Think I have it cured at my house.
2007-03-09 17:26:21
·
answer #3
·
answered by Anonymous
·
0⤊
0⤋
Mould is caused by water not evaporating and causes the bacteria to grow. You need plenty of air circulation and to dry exposed surfaces out. I would clean the area well with a solution of bleach and water, keep windows open as much as possible and have an extractor fan installed.
2007-03-04 19:30:48
·
answer #4
·
answered by jntt_bnks 3
·
0⤊
0⤋
good luck with mold. they have some kind of paint out you paint over the mold. it's suppose to stop it. you have to clean the mold off first before applying it. try vinegar. you got mold because it stays damp all the time. if you dry after bathing you might not have the mold problem. you might have moisture in your walls. like i said, good luck.
2007-03-04 19:12:49
·
answer #5
·
answered by Anonymous
·
0⤊
0⤋
Do the bleach thing as suggested, then repaint the wall with mould prevention paint. Works a treat. And you are right about the coldest wall - its probably the coldest wall in the entire house - try keeping the window open a crack all the time.
2016-03-29 00:37:04
·
answer #6
·
answered by Marilyn 3
·
0⤊
0⤋
Mix water and bleach and spray it on the mold, it will go away.
2007-03-04 19:03:53
·
answer #7
·
answered by ßαßε 5
·
0⤊
0⤋
Clean your shower daily
2007-03-04 19:03:53
·
answer #8
·
answered by my_craig1 2
·
1⤊
0⤋
you have to clean it with bathroom sprays and try to keep it dry . i always clean it after i take a bath and then i turn on the electric dryer to dry the room . one convenience i love here in japan . they have ac/dc and dryer setting in the bathroom .....
2007-03-04 19:05:31
·
answer #9
·
answered by asphyxia 5
·
0⤊
0⤋
Bleach. And don't rinse it off.
2007-03-04 19:04:03
·
answer #10
·
answered by Just me. 4
·
0⤊
0⤋