please tell me how to clean old brass in an inexpensive way other than brasso as its a big piece also how to?

Question

remove laquer

Answer 1

My Grandma Always Used Baking Soda.. Or Tooth Paste.
Then Buff It With A Soft Cloth.

Answer 2

There is a product that you can purchase at most Home Hardware stores called..Never Dull. It is very inexpensive and will last you a very long time. I used to make bronze, brass and silver jewellry and this is what I used. You just pull a piece out..rub item..wait a min. then wipe with dry cloth. I paid 4.99 for mine and it lasted approx.a year with regular use. Good luck.The only way I know of to remove laquer is with a heating gun.

Answer 3

Restored lots of brass products when I had save. The cleansing soap & water scrub is a sturdy initiate. Small possibility the products are plated so verify w/ a kitchen magnet . Any severe cleansing or buffing can eliminate it. would evade coarse abrasives, acids or caustics. chemical compounds can alter the layer of oxidation & reason the brass to circulate crimson or gray & make it extra durable to to eliminate. terrific to eliminate the brasses & attempt a brass brush on a handle or a rotary brush on a drill to eliminate any loose corrosion. as quickly as the oxidation is broken & you start to be certain clean steel. Brass polish could paintings w/ some attempt. There are brass refinishing kits attainable from homestead ctrs yet there continues to be a honest quantity of elbow grease mandatory on badly corroded products. approximately$25 potential buffing is terrific yet would evade the small severe speed rotary procedures. without buffing device , sewn buffing wheels & rouges are actually not high priced & would get the biggest which will extra healthy right into a corded drill for DIY. Will eliminate floor tarnish yet you could could stay w/ any deep pitting. On an older piece, evaluate unlikely for a vivid end & do basically adequate to boost highlights. would not lacquer except the brasses are thoroughly wiped clean & degreased. terrific regards

Answer 4

A clear, protective lacquer coating is often applied to copper and brass utensils to retard or prevent tarnishing.

If you are using a lacquered utensil for decorative purposes only, this finish may be left on and needs only to be occasionally wiped with a soft cloth to keep it clean.

If the item is to be used for cooking, on direct heat, or if it will come in contact with very hot water, the coating must be removed.

It is essential that all coating is removed before using on direct heat or with very hot water. Failure to do so will result in unsightly spotting that you'll only be able to remove with strong buffing.

Check the product label and its specific instructions on removing the lacquer. Some lacquers can be removed using a homemade solution; stronger lacquers require a commercially available lacquer removal product.


Commercial Removers

The easiest way to remove the coating is with a commercial lacquer remover, such as Parks' refurbisher or Behr's The Stripper, available at hardware and paint stores. Follow the instructions and repeat the process until all lacquer is removed, especially in small crevices.


Homemade Solution

Make a mixture of Baking Soda and Water (1 Tablespoon of Soda to each Quart of Water) and bring to a boil.

While still boiling, immerse the item. One half at a time if your pot of solution is not large enough to immerse the item completely.

After about 15 minutes of boiling, the coating will peel and lift off. Remove from the solution and wash with hot water. (Remember to protect your hands from hot surfaces.)

Use acetone (or non-oily nail polish remover) on a cotton or wool pad to remove any remaining stubborn coating.

Answer 5

Lemon and baking soda. Dip the cut lemon in baking soda and rub on the brass. Works for copper too.

The Syko Ward

Answer 6

White Vinegar and a green scrubby.Soak it, if you can and then use green scrubby, wipe with soft damp cloth.

Answer 7

Try boiling it in baking soa water