2007-02-28 01:46:02 · 19 answers · asked by Anonymous in Home & Garden ➔ Maintenance & Repairs
I agree with H-Vaker, many answers given to you are appaling! Simply cut out the section of pipe, replace with a new section.
Easiest method is just to purchase two push fit sockets, either 15mm or 22mm, depending on how thick your pipe is. Problem fixed in about two minutes.
The only problem I could forsee is if your copper pipework is 3/4 inch, then unless you have knowledge of copper fittings and soldering then you will need to call in a plumber to renew your section of pipework. Try the push fit sockets first, if they are slightly too big for the pipework, call in a plumber.
2007-03-01 21:02:29 · answer #1 · answered by rikerlock 4 · 0⤊ 0⤋
A pin hole in a copper pipe is very easy to repair, for a permanent repair all you need is an electric soldering iron, some solder, and a little bit of steel wool, the total cost of these would not be more than £20.00, a lot cheaper than a plumber.
First turn the water off to release the pressure and run the taps and the toilet which will get some of the water out of the pipe, clean around the pin hole with steel wool until it's shining bright and wipe with a clean cloth, don't touch the area with your fingers, apply the soldering iron to the pin hole until it's very, hot the pipe will take some of the heat away so give the iron plenty of time to heat the pipe then apply the solder and iron to the pin hole at the same time, and the job is done, get a soldering iron of at least 30 to 40 watts.
All this might seem complicated but it is really very simple, some people have problems with soldering but this is due to; they don't clean the joint and don't apply enough heat.
If the pin hole is on the top of the pipe it is a lot easier but with patience you should be able to do it.
2007-03-03 13:56:29 · answer #2 · answered by John L 5 · 0⤊ 0⤋
Copper Pipe Repair
2016-11-09 21:56:13 · answer #3 · answered by Anonymous · 0⤊ 0⤋
It really depends on where the pinhole is located. If it is on or near a fitting, such as an elbow or union, you will more than likely have to re-solder it. If it is on a straight piece of pipe, you can use a repair clamp. Teflon tape won't do the trick because it is mainly used for sealing threads when joining threaded fittings. It will not hold the water pressure in the pipe. The best way to go, in order to prevent the pinhole from leaking in the future, is to cut off the piece where the pinhole is located and repair it by sweating a repair coupling on the pipe. Repair clamps are good and will hold the pressure in the pipe. I've never seen one of these leak in the past.
2007-02-28 02:02:00 · answer #4 · answered by Joey 4 · 3⤊ 0⤋
There is a way to DIY if you feel able enough. You will need two 15mm Compression straight connectors a short piece of 15mm copper pipe, a junior hacksaw and some sandpaper. If it is a 22mm pipe then get the same fittings and pipe in this size. Drain down the pipe work to get the water out. Cut either side of the pinhole, about 4 ins. each side. Rub sandpaper around the cut to remove the burr of metal Slide connector onto pipe and tighten with spanner. Do the same the other end of pipe. Cut copper pipe to the correct length and fit to compression joints Tighten fittings and refill pipework.
2007-02-28 03:01:51 · answer #5 · answered by Anonymous · 4⤊ 0⤋
As a plumber I'm getting chills from reading these answers especially the hitting it with a hammer one. Of course the best way to repair it is to replace the pipe but if you can't they make a thing that we called bandaids which is nothing more than a strip of rubber and clamp with two bolts sometimes have a hinge on one side, you might be able to pick one up at Home cheapo. P.S. If you do tap it with a hammer get more bandaids you'll need them.
2007-02-28 14:50:23 · answer #6 · answered by H-vaker 2 · 1⤊ 0⤋
They make plumber's epoxy that dries hard as steel. It may work. I'd secure that with some GOOP. It's fantastic glue.
You should cut the pipe with a pipe cutter and solder in a coupling.
2007-02-28 02:51:54 · answer #7 · answered by ? 6 · 0⤊ 0⤋
If You Have The Right Tools. Tubing Cutter and 2- adjustable Cresent Wrenches. Cut Tubing where pin hole is and put Compression Coupling on It.
2007-02-28 01:57:34 · answer #8 · answered by bob r 4 · 2⤊ 0⤋
I agree, been there seen it and done it!!! chewing gum does work but if you dont have any then teflon tape does work, that is until you put the floorboard back and put a nail through the copper!!!!!!!! I am sure I am not the only one to do this. Then replace the section with plastic pipe and push fittings from B&Q they work a treat.
2007-02-28 01:56:37 · answer #9 · answered by tony k 1 · 0⤊ 1⤋
Yes, you can easily repair that pinhole yourself.
Take some ordinary black electrical tape wrap it around the pipe over the pinhole. Then take an ordinary stainless steel hose clamp and put that over the tape/hole and tighten it down. The repair is permanent and will not leak and lasts indefenitely.
Get the tape and hoseclamp at Lowes or HomeDepot or Hardware store
2007-02-28 03:08:27 · answer #10 · answered by James M 6 · 0⤊ 3⤋