My 14 yearold Maytag top loading washing machinehas started to make a loud sortof squealing sound. It just started to do this. I think the noise started when the machine was full of water and started the aggitator. I stoped it took the clothes out and turned it back on, that made no differance. I put it on spin mode that made no differance.
ANY SUGGESTIONS
2007-02-17 12:11:05 · 6 answers · asked by danzka2001 5 in Home & Garden ➔ Maintenance & Repairs
It sounds like there is something stuck in the pump and the pump belt is squeaking. Remove the two screws that hold the front panel on located about 4" up and 2" in on each side and swing the panel up and disengage the clips at the top. You will see the pump on the right and the belts are under the machine.
Clear the pump and replace the belts. The belts come as a set under part number 12112425 . If the belts have not been changed on over a year they are due. Since you have had squeaking the belts need to be changed regardless.
2007-02-17 13:24:45 · answer #1 · answered by Anonymous · 1⤊ 0⤋
A washing machine may wiggle, rattle or move across the floor. It is often accompanied by excessive noise. There can be several causes and the problem is worse with some machines more than others.
The most common cause is an unbalanced wash load. Open the lid and when it comes to a stop, redistribute the clothing to balance the weight. Heavy loads, especially things like comforters, are more likely to become unbalanced than small loads. If you do a lot of heavy loads, you should consider a heavy duty/large capacity washer when it comes time to replace your current unit.
A washer must be level both from side to side as well as from front to back. Washing machines have adjustable feet to enable you to level them.
The outer tub is supported by springs, pistons or counterweights to keep it balanced. The weight of all that water in a wash load requires a powerful balancing mechanism. If the balancing system becomes detached from one or more points, it will not be able to balance the load properly. Furthermore, even if everything appears to be in place, as the appliance ages, the springs or pistons may begin to wear out and not support as much weigh as needed.
Unplug the washer and open the cabinet. Because of the variety of balancing mechanisms, you will have to inspect your machine to determine how it is balanced. Once you discover the mechanism, then inspect it for integrity. In the case of old parts that appear to be in working order, you may not be able to tell if they need to be replaced. They may be weak but appear to be in good condition. If no other solution resolves the problem, then replacing the balancing springs or other moving support parts may be called for.
Another common cause for excessive movement is the floor on which the washer rests. The washer is heavy and even more so when filled with water. Any floor, other than a concrete slab, will tend to pick up and amplify the vibrations from the machine.
There are a couple things you can try. If you have access to the joists under the floor, you may be able to beef up the support. Another thing to try is placing a large sheet of plywood under the washer. It should be 3/4" or even 1" thick and as large as possible to distribute the weight. Use a sheet big enough for both the washer and dryer to sit on. If possible fasten the plywood to the existing floor.
2007-02-17 12:22:31 · answer #2 · answered by ? 3 · 0⤊ 1⤋
i'd suggest that you try posting your question again later. there is an 'appliance guy' that is on and he knows his stuff. also, describe whether the squeal is a metal on metal, or rubber belt type of squeal. if it's metal, it could be a worn out clutch or brake, that locks the transmission in gear. if it is a belt squeal, the belt(s) could be worn and slipping. if you have never changed the belts, they are old enough, they're due. i'm not sure if your maytag is the old style with 2 belts under the base or not. but if it is, replace the motor rollers and springs when you change the belts. the rollers and springs come in a kit and tension the belts and shift the motor from agitate to spin. good luck, hope this helps.
2007-02-17 12:53:26 · answer #3 · answered by car dude 5 · 1⤊ 0⤋
call the shop the place you acquire the device and tell them you like a alternative, ideally yet another type. in case you acquire at Lowe's or domicile Depot, you have 60 days to teach it lower back in for a complete alternative (of a staggering, quiet front loader) or refund. different than that, is your device completely balanced? Even being somewhat off stability could make for a noisy device. i recently have been given a Whirlpool dishwasher after swearing i'd by no ability purchase yet another Whirlpool equipment lower back (how quite we are swayed by ability of value reductions and sales communicate) and that i traded it in for yet another type. subject solved.
2016-11-23 15:46:12 · answer #4 · answered by Anonymous · 0⤊ 0⤋
sounds like the belt has given up. make a note of the model number and order a new one. also easy to replace from the rear of the machine.
good luck
2007-02-17 12:17:52 · answer #5 · answered by Richard C 2 · 1⤊ 0⤋
I have to admit Mr. Appliance you know your stuff and I am glad to see someone else who knows what their talking about! I have been doing mechanical maintenance for years and got so frustrated so now I'm a truck driver. P.S. you better listen to this guy, because I think he's right!
2007-02-17 13:46:26 · answer #6 · answered by Anonymous · 1⤊ 0⤋