English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

2007-02-14 05:51:51 · 7 answers · asked by halojosh21 1 in Home & Garden Maintenance & Repairs

7 answers

A radioactive element called Americium, releases particles as it decays, and when smoke interupts the flow of particles, that triggers the detector to go off. But the Americium is in such small quantities that it could never cause harm or radiation poisoning.

2007-02-14 06:00:00 · answer #1 · answered by Josh 2 · 1 1

There are two main types of smoke detectors: ionization detectors and photoelectric detectors. A smoke alarm uses one or both methods, sometimes plus a heat detector, to warn of a fire. The devices may be powered by a 9-volt battery, lithium battery, or 120-volt house wiring.

Ionization Detectors

Ionization detectors have an ionization chamber and a source of ionizing radiation. The source of ionizing radiation is a minute quantity of americium-241 (perhaps 1/5000th of a gram), which is a source of alpha particles (helium nuclei). The ionization chamber consists of two plates separated by about a centimeter. The battery applies a voltage to the plates, charging one plate positive and the other plate negative. Alpha particles constantly released by the americium knock electrons off of the atoms in the air, ionizing the oxygen and nitrogen atoms in the chamber. The positively-charged oxygen and nitrogen atoms are attracted to the negative plate and the electrons are attracted to the positive plate, generating a small, continuous electric current. When smoke enters the ionization chamber, the smoke particles attach to the ions and neutralize them, so they do not reach the plate. The drop in current between the plates triggers the alarm.


Photoelectric Detectors

In one type of photoelectric device, smoke can block a light beam. In this case, the reduction in light reaching a photocell sets off the alarm. In the most common type of photoelectric unit, however, light is scattered by smoke particles onto a photocell, initiating an alarm. In this type of detector there is a T-shaped chamber with a light-emitting diode (LED) that shoots a beam of light across the horizontal bar of the T. A photocell, positioned at the bottom of the vertical base of the T, generates a current when it is exposed to light. Under smoke-free conditions, the light beam crosses the top of the T in an uninterrupted straight line, not striking the photocell positioned at a right angle below the beam. When smoke is present, the light is scattered by smoke particles, and some of the light is directed down the vertical part of the T to strike the photocell. When sufficient light hits the cell, the current triggers the alarm.

Which Method is Better?

Both ionization and photoelectric detectors are effective smoke sensors. Both types of smoke detectors must pass the same test to be certified as UL smoke detectors. Ionization detectors respond more quickly to flaming fires with smaller combustion particles; photoelectric detectors respond more quickly to smoldering fires. In either type of detector, steam or high humidity can lead to condensation on the circuit board and sensor, causing the alarm to sound. Ionization detectors are less expensive than photoelectric detectors, but some users purposely disable them because they are more likely to sound an alarm from normal cooking due to their sensitivity to minute smoke particles. However, ionization detectors have a degree of built-in security not inherent to photoelectric detectors. When the battery starts to fail in an ionization detector, the ion current falls and the alarm sounds, warning that it is time to change the battery before the detector becomes ineffective. Back-up batteries may be used for photoelectric detectors.

2007-02-14 05:55:41 · answer #2 · answered by Anonymous · 1 0

There are two types of smoke detectors commonly used in home. 1st one detects smoke particles in the air. The 2nd one picks up the heat from a fire. Which one to use: 1st one in bedroom and hallways, the second one in the kitchen area.

2007-02-14 06:00:03 · answer #3 · answered by Boomrat 6 · 1 0

Americium... radioactive substance... emits a stream of subatomic particles towards a sensor... smoke gets in the way of the stream of particles, which breaks the circuit, which triggers the alarm to go off

2007-02-14 05:55:10 · answer #4 · answered by Anonymous · 0 0

Batteries, smoke

2007-02-14 05:59:57 · answer #5 · answered by Anonymous · 0 0

Smoke....and possibly batteries or electricity.

2007-02-14 06:00:05 · answer #6 · answered by bry leigh 2 · 0 0

smoke! like get a match then lite it then but it out right under it! it worked for me!

2007-02-14 05:56:24 · answer #7 · answered by Anonymous · 1 0

fedest.com, questions and answers