My computer's got a 2.4 ghz processor and 512 ram already in it. I need more. All I know is where in the computer the new memory is supposed to go.
What else do I nee to know?
2007-02-14 04:11:57 · 11 answers · asked by Can I Be Your Pet? 6 in Computers & Internet ➔ Hardware ➔ Other - Hardware
haha! sweetpea, that was a beautiful reply, wasn't expecting it... i think the memory i got was probably not compatible... either that or I need an upgrade.
2007-02-16 03:42:46 · update #1
(VERY) New computers use DDR2 RAM which slots into one of 4 slots. With DDR2 you must pair up the ram in the slots. So you need to buy two of the same capacity (i.ei 2 x 512).
These are plug and play as they go in new computers usually running XP, which supports plug n play.
If you're using older ram (DDR and SDRAM) then I think you need to install it first!
2007-02-14 04:19:25 · answer #1 · answered by rock n roll maiden 1 · 0⤊ 0⤋
For as long as I can remember, most motherboards are designed for you to just plug the memory in.
Motherboards have limits to the amount of memory they will support. Some require memory to be inserted two sticks at a time.
The speed of the memory you need will depend upon the motherboard, the cpu and the system speed.
The operating system will just detect your new memory and work.
You need to ensure that the new memory you put in is of the same speed as that already fitted and is suitable for your motherboard.
Checkout the motherboard instruction book if you have it. If necessary, take it along to the shop when you buy your memory and ask them for advise.
2007-02-14 06:45:21 · answer #2 · answered by David P 7 · 0⤊ 0⤋
Its plug and play your system will detect the new added memory space when it boots up. Just make sure it is compatible with your motherboard, otherwise it won't work at all. Try researching what type of memory card is accepted by your motherboard and how it is supposed to be installed. (Hint - memory card installation come in pairs and be sure to get the right clocking) Good luck.
2007-02-14 04:17:55 · answer #3 · answered by Anonymous · 0⤊ 0⤋
RAM is Plug n' Play, your elementary enter Output gadget (BIOS) will immediately configure your voltage and timing settings for optimal performance, you may change those settings in case you want (Over Clocking) although the outcomes might want to be volatile on your workstation.
2016-11-03 10:40:17 · answer #4 · answered by Anonymous · 0⤊ 0⤋
It depends on the age of the computer as to whether its plug and play or needing to be installed but I would say plug and play if its a 2.4GHz CPU
2007-02-15 02:56:14 · answer #5 · answered by gerard mcmanus 2 · 0⤊ 0⤋
You need to know the type of RAM, go online to www.crucial.com for free analysis of your setup & recommendations for increasing. (Not an advert, by the way, just a recommendation) You don't need to buy your RAM from them.
Installation is indeed "plug 'n play", but take precautions to turn the power off & to avoid static.
2007-02-14 04:18:34 · answer #6 · answered by champer 7 · 0⤊ 0⤋
you have to make sure to get the right kind. pull out the memory thats in there with the machine OFF, write down the type, search the web or go to store. after you have the right kind, its "plug and play" but you plug it in with the machine off, then turn on and play.
2007-02-14 04:16:29 · answer #7 · answered by ecoandy 2 · 0⤊ 1⤋
just plug in and play as simple as that
2007-02-14 04:24:03 · answer #8 · answered by Anonymous · 0⤊ 0⤋
plug and play...but you have to have the right type for it to work.
2007-02-14 04:15:53 · answer #9 · answered by mnid007 4 · 1⤊ 0⤋
your born with it
2007-02-14 04:16:38 · answer #10 · answered by # 1 sweet pea 2 · 0⤊ 2⤋