use a putty knife to scrape the wax off then brush off the excess soot. after that you can use a high heat spray paint to paint the bricks (usually black) in order to give that clean look
2007-01-27 06:43:13
·
answer #1
·
answered by outofmymind 4
·
0⤊
0⤋
What a great question. I use all purpose orange cleaner. Works great. Spray on and return shortly with a brush, scrub and rinse with spray bottle of water. Looks like new. My fireplace was built in the early 60's. Works great......
2007-01-27 08:48:49
·
answer #2
·
answered by Anonymous
·
0⤊
0⤋
in the past commencing a scrub consultation, verify the brick to make effective that that's in sturdy shape. some incredibly previous brick may well be crumbly and you in no way prefer to take a broom to that. If the brick is sealed that's lots much less perplexing to scrub, so no depend if that is no longer at the instant that is needed to get that executed. First you will prefer to truly get it sparkling. Then purchase a penetrating sealer that is composed of Tung oil. The foaming scrubbing bubble stuff which you sparkling the washing room with works nicely. listed under are 4 different innovations: formula a million: mixture one ounce of cleansing soap and one ounce of table salt with adequate water to make a cream. Rub mixture into brick floor with textile; enable to dry a minimum of ten minutes and do away with with stiff brush. (the stiff brush area sounds like complicated artwork-salt isn't known for it’s cleansing ability) formula 2: Make a thick mix of cleansing soap or detergent, pumice, a sprint ammonia and warm water. Paint the aggregate on the exterior and enable dry. Rub off with a moist scrub brush. you're utilising alkali and a tender abrasive to do away with the greasy soil. (extremely a mix…lower back with the stiff brush) formula 3: Shave a bar of naptha cleansing soap right into a field and upload 3 quarts of water. carry mixture to an entire boil until the cleansing soap melts. Cool. upload a million cup ammonia and one pound of pumice. mixture thoroughly. Brush in onto all sooty surfaces and enable stand one hour or extra. Rub off with a stiff-bristle brush. Rinse “****” away with heat water, then end off with a medium to reliable detergent and rinse lower back with heat water. (this sounds too complicated to make…too many steps) formula 4: Dissolve 8 tablespoons (a million/2 cup) Trisodium Phosphate (TSP) or **** & Span in one gallon of warm water. With stiff scrub brush, scrub brick floor. Rinse with a great number of warmth water. Repeat if soot or greasy stain isn't bumped off. extra TSP may well be extra if mandatory, as much as a million cup in line with gallon. it incredibly is an extremely reliable answer; stay away from getting on epidermis, carpet, or fabric. (acid is risky and extra appropriate left to the experts)
2016-11-01 10:35:43
·
answer #3
·
answered by Anonymous
·
0⤊
0⤋
With Elbow Grease and a Scrub Brush!
2007-01-30 06:22:12
·
answer #4
·
answered by Andi S 2
·
0⤊
0⤋
Concrete cleaner
2007-01-27 12:32:36
·
answer #5
·
answered by ? 3
·
0⤊
0⤋
use muriatic acid but use precaution stuff is potent but it will clean any brick cement tiles guarenteed , again read the label and follow directions
2007-01-27 07:25:33
·
answer #6
·
answered by high1315 2
·
1⤊
0⤋
plain soap and water with a soft bristled brush
2007-01-27 06:52:31
·
answer #7
·
answered by Wee 1
·
0⤊
0⤋