2007-01-26 13:57:21 · 12 answers · asked by De Lorme B 2 in Home & Garden ➔ Do It Yourself (DIY)
Possibly. You need to determine the amperage required and see if it is less than 15 amps. If the wattage is marked on the manufacturer's label but not the amps, divide the wattage by the voltage to get the amperage.
2007-01-26 14:04:55 · answer #1 · answered by MT C 6 · 0⤊ 0⤋
If the amp rating of the water heater is less than 15 amps, you can do it. More than likely it will be 20 amp rating. Also if there are other outlets on the same circuit and something else is plugged in such as a blow dryer, the breaker is going to trip or the fuse will blow. I'd recommend a single outlet on a 20 amp breaker for uninterrupted hot water.
2007-01-26 14:11:53 · answer #2 · answered by Likalotapus 4 · 0⤊ 0⤋
Some electrical devices use watts to express their power consumption, like heating elements, base boards, light bulbs.
When we say 120v it is in reality something between 115v and 117v due to tension variations. So to play safe we usually calculated with 115v.
One Amp at this voltage = 115watts
115amps x 15=1725amps
If the heating element is rated lower, than you'll be ok to plug the tank in the 15amp outlet.
2007-01-26 14:41:02 · answer #3 · answered by Abaris 3 · 0⤊ 0⤋
not knowing the amperage requirement or wattage of the unit, I can't come to conclusion from your question. It's faily simple to figure though. Somewhere on the heater it should either state the amp requirements or wattage. If the amps stated are less than 15, you're good to go. If it only provides watts, divide the watts by 120, (watts/voltage=amps) and you know the amperage draw. good luck.
2007-01-26 14:23:56 · answer #4 · answered by Dale D 2 · 0⤊ 0⤋
You should be able to look at the amperage requirements on the specs sheet stuck to the water heater. It usually has a bunch of information such as the model number, serial number, and voltage/amperage requirements. If it is less than 15, sure!
2007-01-26 14:03:44 · answer #5 · answered by Anonymous · 0⤊ 0⤋
no its most likely overrated and will trip the breaker
water heater must also be on a dedicated circuit by the NEC 2005
(national electrical code 2005)
look at the name plate rating on the heater and see what it calls for
if its continuous load you have to do the calcs for it
check the NEC book for all the calcs
the book isnt cheap as this is a pro. job
2007-01-26 14:28:26 · answer #6 · answered by D S 3 · 0⤊ 0⤋
yes but to be sure read the label on the hot water heater for the amp ratting
2007-01-26 14:01:22 · answer #7 · answered by rooterdon2000 2 · 1⤊ 0⤋
No, I think if you check the rate plate you will find it is 20 Amps.
2007-01-26 14:02:17 · answer #8 · answered by Anonymous · 0⤊ 0⤋
um well i plug my 15 amp for my guitar into a 120 volts house... if that even applies
2007-01-26 14:25:06 · answer #9 · answered by lilanizzle 2 · 0⤊ 0⤋
Most likely not. I am willing to bet the water heater is 20amps
2007-01-26 14:50:44 · answer #10 · answered by Anthony A 3 · 0⤊ 0⤋