I bought new PC, everything was fine until i decided to burn some cd/dvd. The nero v.6 just hanged up after cashing files.... i returned my dvd burner and got another one, installed nero v.7changed the cable, and set the burners jumper to master...the same...just this nero now generates a log file, which gives me no sense...any help would be appreciated...
error from log:
22:26:46#30 CDR -1502 File ThreadedTransferInterface.cpp, Line 1783
DMA-driver error, CRC error
D: _NEC DVD_RW ND-3540A
22:26:46#31 TRANSFER -27 File ThreadedTransferInterface.cpp, Line 1783
Could not perform start of Disc-at-once
22:26:46#32 Phase 34 File dlgbrnst.cpp, Line 1724
Simulation failed at 24x (3.600 KB/s)
Existing drivers:
File 'Drivers\scsiport.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=96256 bytes, created 2004.08.04 14:00:00 (Adapter driver for src)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
2007-01-24 08:31:28 · 6 answers · asked by influenza 2 in Computers & Internet ➔ Hardware ➔ Other - Hardware
1. tried 3 different types of media
2. without simulation it just starts burning, and media goes to waste...
3. cable is 80pin
4. its Coer2Duo
5.HDDs are on sata, so not on the same connection
6.uninstalled controler and rebooted so XP coud install drivers again...same lame....
7. NEC or Pionier its not about brand. Thanx.
2007-01-24 08:58:18 · update #1
7. I try to burn some data, actually any data, so no other soft like dvdshrink is needed...
8. This burner worked perfectly with celeron 900MHz earlier btw :)
2007-01-24 09:01:46 · update #2
update the driver.
2007-01-31 00:08:49 · answer #1 · answered by Anonymous · 0⤊ 0⤋
If the hardware is set up properly like the guys above have said then are you trying to burn a DVD or a CD? If its a DVD you will need to decrypt the data on the disc before you can use use Nero to write the disc. Nero will not always burn copy protected discs. Try using DVD decrypter to rip the disc, then if it is a 2 layer disc you will need to shrink the disc image. I use DVD Shrink, but there are other programs you can use. Once that is completed then you can write the image onto a disc, I use Imgburn to do this. There are programs out there that will do multiple steps for you, but you have to be sure you use a program that will break the encryptions on the disc.
2007-01-24 08:40:38 · answer #2 · answered by Scotty 6 · 0⤊ 0⤋
Untick the "simulation" box when you burn the disc. This wastes time and makes the app unstable - this is causing the error.
Some other issues can cause the "DMA-driver error, CRC error":
Bad disc brand, try using a different type or + instead of - or vice versa.
Bad IDE cable
Bad IDE controller
P.S Do not listen to the person below, Pioneer and LG drives are just as prone.
2007-01-24 08:36:00 · answer #3 · answered by jobo 2 · 0⤊ 0⤋
Get rid of your NEC Writer and try
an LG / Pioneer 111 / Samsung or Liteon
Make sure you have an 80 pin cable connected to the drive and NOT a 40 pin cable otherwise you get all sorts of problems.
Make sure your are not running it on the same channel as the primary hard drive
ReInstall you Adaptec drivers
Use Ritek, Ridata or Traxdata minus discs
Hope this helps
BTW its not a celeron processor is it ?
2007-01-24 08:40:24 · answer #4 · answered by id36uk 3 · 0⤊ 0⤋
Like jobo says also slow the burn rate down it may well be over running the buffers.better still look for imgburn on www.downloads .com much better than nero.
2007-01-24 08:40:40 · answer #5 · answered by taxed till i die,and then some. 7 · 0⤊ 0⤋
sounds like a driver problem, any other software other than nero?
2007-01-29 12:35:22 · answer #6 · answered by Daniel S 2 · 0⤊ 0⤋