2007-01-23 17:23:30 · 10 answers · asked by JORGE J 1 in Home & Garden ➔ Maintenance & Repairs
Drill the concrete and install lead anchors at 2 foot intervals and staggered. Drill the sole plate and screw it down. attach the top to the existing ceiling joist. Don't forget the door.
2007-01-23 17:30:30 · answer #1 · answered by Anonymous · 0⤊ 0⤋
If you want it legally done and don't want your wall to eventually fall down. I suggest you get a jack hammer and remove at least a 12x12 square in the corners of the concrete. Follow these steps
Remove debris from there
Dig at least 8 inches deeper
Fill up with new concrete mixture
Use anchors that support a 2x4
Then go 3 1/2 feet and do the same thing
Once all beams are set up start building your wall
2007-01-23 17:44:19 · answer #2 · answered by Anonymous · 0⤊ 0⤋
You have to build your wall first. (2x4's) I suggest your buy a compresser as your job will be much easier. Grab a single 2x4 and put it where you want your wall to be every two feet you need to punch in some bolts. (they are about an inch wide or so) So you will have to drill through the 2x4 and into the concrete. Nail your wall into the bottom 2X4. use supports if you are planning on leaving it over night.
2007-01-23 17:30:08 · answer #3 · answered by Mr. Sir 5 · 0⤊ 0⤋
the upward thrust joint is basically a divider between sections of the concrete. like in case you have an exsisting slab, and choose to feature onto it for a room, then you extremely sort up the fringe of the hot slab, and the suited the place the hot concrete will meet the outdated, you sort a one-with the help of four board up against the exsisting concrete, to make a separation. then, after the hot pour solidifies, you are able to fill in what ever hollow is left with advance compound- a demanding rubbery seal between the two slabs interior the joint. that way, if the floor shifts, the concrete wont crack there, it won't harm yer beginning up. it makes room for geological moving.
2016-12-16 16:00:28 · answer #4 · answered by ? 4 · 0⤊ 0⤋
The foot plate is attached to the floor with masonry nails or nails set by a powder charge. Beyond that, the construction is conventional.
2007-01-23 17:32:04 · answer #5 · answered by Anonymous · 0⤊ 0⤋
You can use a ram set or drill holes in concrete and use expansion bolts then frame as usual. You can rent all those tools.
2007-01-23 17:31:39 · answer #6 · answered by adevilchild38 5 · 0⤊ 0⤋
Yes. This is common in garages, the beams are braces when they cannot be inset in concrete. The bracing is parallel and lateral.
2007-01-23 17:27:29 · answer #7 · answered by S T 5 · 0⤊ 0⤋
you just need a drill and bit that will go through concrete. they have them cheap on ebay. here's a direct link
2007-01-24 01:53:08 · answer #8 · answered by jbowhard 4 · 0⤊ 0⤋
buy a tap-con bit and some tap-con screws (3 in.) and when your wall is in place drill into floor and screw it down.
2007-01-25 08:30:34 · answer #9 · answered by Anonymous · 0⤊ 0⤋
not sure
2007-01-27 03:57:38 · answer #10 · answered by jerry 7 · 0⤊ 0⤋