2007-01-16 12:37:09 · 8 answers · asked by Anonymous in Cars & Transportation ➔ Car Makes ➔ Chevrolet
i dont need them but if you do try on ebay or autozone.sometimes it is very simple to hook it up for your car.try turning the key on and off 10 times until the horn beeps and then hit one of the buttons on the remote and it may work then.I swear thats how i programmed mine for my 01 impala
2007-01-16 12:42:25 · answer #1 · answered by kevin m 4 · 0⤊ 0⤋
NOTE: Before entering the remote transmitter programming mode, make sure that the vehicle battery is fully charged and that the anti-theft system is not armed or triggered (if equipped). Close all doors to make sure conflicting chimes do not sound during programming. Turn the ignition switch from position I to position II four times within six seconds. Turn the ignition switch to position 0. A chime sounds and an LED will illuminate to indicate that the learning mode has been accessed and it is possible to program remote transmitters. Within 10 seconds of the previous step, press any button on the remote transmitter being programmed until a chime is heard and the LED flashes. This indicates a new transmitter code has been successfully received. After each successful remote transmitter programming, another 10 second learning mode is automatically entered, up to a maximum of four times. To program additional remote transmitters, repeat step 5. The system will exit the learning mode if the ignition switch is turned to position III, no new remote transmitter is programmed during the 10 seconds or if four remote transmitters have been programmed. NOTE: An incorrect programming procedure does not affect the stored codes. After successful programming, only the new programmed remote transmitters will be accepted. Test all the programmed remote transmitters, by activating and deactivating the remote locking and unlocking functions.
2016-05-23 22:33:42 · answer #2 · answered by Anonymous · 0⤊ 0⤋
call local dealerships service dept and they will tell you the way to code it. Or if they FOB PROG (Remote Keyless Entry Transmitter Programming): This feature allows you to match the remote keyless entry transmitter to your vehicle.
To match the transmitter:
1. Scroll, using the SEEK up or down arrows, until FOB PROG appears on the display.
2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk next to it. BEGIN will be displayed.
3. Press the DISP button to start programming. When the message PUSH FOG flashes, press and hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter is learned.
4. Repeat Step 3 for each additional transmitter.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.
dont help call GM's cust serv hotline
2007-01-18 11:38:32 · answer #3 · answered by I race cars 4 · 0⤊ 0⤋
Take it to the dealer to have them reprogrammed as you need the tech 2 scanner to reprogram them
2007-01-16 12:43:15 · answer #4 · answered by Rudedude 4 · 0⤊ 0⤋
the dealer must program it via a device called a tech2. won't cost much, maybe $20.
2007-01-17 15:55:23 · answer #5 · answered by RobertB 1 · 0⤊ 0⤋
Go to the Dealer they will show you
2007-01-16 12:41:10 · answer #6 · answered by Douglas R 4 · 0⤊ 0⤋
go to the installer or the dealer
2007-01-16 12:40:29 · answer #7 · answered by Anonymous · 0⤊ 0⤋
NO
2007-01-16 12:39:48 · answer #8 · answered by Anonymous · 0⤊ 0⤋